Access to network interface (Mac-network)

Special Forums UNIX and Linux Applications Access to network interface (Mac-network)

03-08-2012

Registered User

1, 0

Join Date: Mar 2012

Last Activity: 8 March 2012, 9:42 AM EST

Posts: 1

Thanks Given: 0

Thanked 0 Times in 0 Posts

Access to network interface (Mac-network)

Hi,

I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that.

berny88

View Public Profile for berny88

Find all posts by berny88

Previous Thread | Next Thread

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

2. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a...

3. IP Networking

network interface -

Hello, Please, how can i create a network interface with a routable IP address on linux (ubuntu) ? AND How can i desactivate an interface? Thank you so much for help.

4. IP Networking

Network interface-

Hello, Please what's the difference between: AND Thank you so much

5. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks

6. Solaris

Network interface problem

HI, genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex genunix: WARNING: ce0: fault detected external to device; service degraded genunix: WARNING: ce0: xcvr addr:0x01 - link down genunix: NOTICE: ce0: fault cleared external to device; service available genunix: ...

7. UNIX for Advanced & Expert Users

Network interface goes down intermittently

Hi all, I'm using an HP Proliant server with double NIC and Debian 5 (Lenny) as its OS. I used link bonding on it for several years with no problem. Today, (now only one interface connected to switch) the interface went down. I restarted networking service (/etc/init.d/networking restart) and...

8. AIX

Problem with a Network Interface

Hi every body, I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN. When I tried to set this interface UP I encountered the following error: Method error...

9. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt

LEARN ABOUT CENTOS

nm-connection-editor

NM-CONNECTION-EDITOR(1) 				      General Commands Manual					   NM-CONNECTION-EDITOR(1)

NAME

       nm-connection-editor - network connection editor for NetworkManager

SYNOPSIS

       nm-connection-editor  [ OPTIONS ]

DESCRIPTION

       nm-connection-editor  is  a  GTK-based application to add, remove, and modify network connections stored by NetworkManager.  NetworkManager
       must be running for any network connections to be added, removed, or modified.

OPTIONS

       -t, --type=<type>
	      Type of connection to create or show.  Values are NetworkManager setting names, eg  "802-3-ethernet",  "802-11-wireless",  "bridge",
	      "bond", "wimax", "infiniband", "vlan", etc.  Does nothing if --create or --show is not given.

       -s, --show
	      Expand or collapse the network list to highlight the network connection type given by --type.

       -c, --create
	      Create a new connection of the type given by --type and allow the user to modify connection details.

       -e, --edit=<uuid>
	      Show the network connection edit window for the connection of the given UUID.

SEE ALSO

       nmcli(1), NetworkManager(8), nm-applet(1).

								 15 February 2013					   NM-CONNECTION-EDITOR(1)

UNIX and Linux Applications