Visit Our UNIX and Linux User Community

a new soundcard question

Thread Tools Search this Thread
Special Forums UNIX and Linux Applications a new soundcard question
# 1  
Old 08-10-2009
a new soundcard question


i just got a new soundcard its the encore 5.1 channel surrand sound card
enm232-6c1a and i need some help configuring it to my doesnt
have any instreuctions as to how to config it to use with audacity..thanks.


Previous Thread | Next Thread
Test Your Knowledge in Computers #218
Difficulty: Easy
A peer-to-peer network sets all connected computers equal and all connected computers share the same abilities to use resources available on the network.
True or False?

7 More Discussions You Might Find Interesting

1. Programming

C++ little question

Hi, I am doing a C++ self-study and I got stuck with this problem. I want to have a code that asks the suer to enter two numbers and then it lists the numbers between these two numbers. It has also to print a message if these two numbers are equal. Here is what I wrote: #include <iostream>... (11 Replies)
Discussion started by: faizlo
11 Replies

2. UNIX for Dummies Questions & Answers

SoundCard.. Again

Hi everyone.I have an Audigy2 ZS sound card. I'm not a guru so don't send me faraway)) Well my card sounds only in front channels... can't setup 5.1. and i can't made a microphone works. PS: A have red this Yuriy Tsibizov (AKA chibis) many time. Here is some system info dmesg Copyright... (0 Replies)
Discussion started by: Levenson
0 Replies

3. AIX

OS Question

What AIX version I need to run a software in a R6000 model 6015/6020 in a IBM P5??? Im implementing a Hot SIte. Is this possible or I need identical systems hardware and software? (1 Reply)
Discussion started by: IBravo
1 Replies

4. UNIX for Dummies Questions & Answers

Vi Question

In Vi, if I have a list of text, and i want to add a semi-colon to the end of each line, does anyone know how to do this? (1 Reply)
Discussion started by: BG_JrAdmin
1 Replies

5. UNIX for Dummies Questions & Answers


Is there any way to use sed and count the number of alphabetic characters in a sentence? (4 Replies)
Discussion started by: brentdeback
4 Replies

6. UNIX for Dummies Questions & Answers

another question?

what happens if the script doesn't get Y,y,N, or n? Will it just loop back up and ask the question again? I tried to get mine to give me another response to tell me my input was invalid, but ran into problems with it. (8 Replies)
Discussion started by: wmosley2
8 Replies

7. UNIX for Dummies Questions & Answers

Next Question:

what is the function of swap in linux why i have to create apsolutely a particion for the swap when i install (i installed lnx4win mandrake and made an automat. disk particion and the install program one of my disk partitions that was 3gb devidet in 4 one native 700mb swap 600mb and the others i... (1 Reply)
Discussion started by: user666
1 Replies
QUISK(1)							   User Commands							  QUISK(1)

quisk - a Software Defined Radio (SDR) DESCRIPTION
QUISK is the software that controls a receiver and transmitter. QUISK rhymes with "brisk", and is QSK plus a few letters to make it easier to pronounce. QSK is a Q signal meaning full breakin CW, and QUISK has been designed for low latency CW operation. It works fine for SSB and AM too. It currently runs under Linux using ALSA sound drivers or PortAudio and offers these capabilities: Quisk can control the HiQSDR. As a receiver it can use the SDR-IQ by RfSpace as a sample source. There are several decimation rates available. The screen shots below were taken using the SDR-IQ. The QUISK receiver will read the sample data, tune it, filter it, demodulate it, and send the audio to the sound card for output to external headphones or speakers. As a receiver it can use your soundcard as a sample source. You supply a complex (I/Q) mixer to convert radio spectrum to a low IF, and send that IF to the left and right inputs of the sound card in your computer. The demodulated audio goes to the same soundcard for output. Quisk can control SoftRock hardware for both receive and transmit. As a transmitter it can control my SSB/CW exciter and my transceiver using Ethernet. As a transmitter it can accept microphone input and send that to your transmitter for SSB operation. For CW, QUISK can mute the audio and substitute a side tone. Quisk can send transmit data to your sound card for use with SoftRock or similar. If you are not using SoftRock hardware and not using Ethernet, then you can modify the C code in microphone.c to connect to your hardware. If you have the SDR-IQ or the Softrock hardware, then QUISK is ready for you to use as a receiver. If you have other receive hard- ware, then you will need to change the file to connect your receiver to QUISK. For example, if you change your VFO frequency with a serial port, then you need to change to send characters to the serial port. The file is written in the Python programming language, a very easy language to learn and use. SETUP
Some deployments of quisk will only need to use sound hardware with ALSA. Other setups will use serial ports (or USB serial ports) and may need permissions set up (perhaps using udev) to allow the quisk program's user access to those ports. See documentation in /usr/share/doc/quisk for more information, as well as configuration file examples. The default configuration file is ~/ The configuration file must be customized for the user (see the commented examples) before running quisk. SYNOPSIS
quisk [options] OPTIONS
-h, --help show this help message and exit -c CONFIG_FILE_PATH, --config=CONFIG_FILE_PATH Specify the configuration file path --config2=CONFIG_FILE_PATH2 Specify a second configuration file to read after the first SEE ALSO Sample config files are in /usr/share/doc/quisk/quisk_conf* copy one, edit and save as ~/ For use with a Funcube Dongle see the program qthid in package qthid-fcd-controller. quisk 3.5.11 January 2012 QUISK(1)

Featured Tech Videos