Good day, everybody! I have a mobile phone (LG Optimus L5) with Android 4.0.3 and a tablet (PocketBook SurfPad 2) with Android 4.1.1 and I have problem with wireless network on these devices. Laptops don't have such problem. My wireless network organisation is a modem connected with an access point... (11 Replies)
I have managed to install Broadcom BCM43228 Wireless adapter on a laptop running CentOS 5.9 using instructions at:
I had the problem "Error for wireless request "Set Encode" (8B2A): SET failed on device... mentioned on the same page and solved... (0 Replies)
I am a new to Ubuntu linux and trying to learn it. I am using ubuntu 10.04. I am getting problem in setting my wireless network. I set it up properly and was working fine. But suddenly it stopped working, though the wireless icon saying that it is connected, but can't load any page. I... (2 Replies)
hi everyone... this is my first post here
please help me with this..as iam new to solaris
i have installed solaris 10 on virtual box.. and am not able to connect to the internet ..
is there anyway i can get connect to the net..
please help me step by step if possible...
thanks in... (1 Reply)
i have wireless usb adapter rtl8187 from micromax company
my proplem is the signal is very weak and i cannot open website
can i increase the signal ?
lo no wireless extensions.
eth0 no wireless extensions.
wmaster0 no wireless extensions.
wlan0... (5 Replies)
I installed solaris 10 x86 on my dell laptop on a partition alongside windows xp. I am able to connect to the internet in xp with both my ethernet local area connection as well as through my wireless network card. But, however i do not have clue as to how to go about it in solaris.
i did not... (0 Replies)
I have a laptop with a Linksys Wireless G PCMCIA card and a cable connection goin into a router and then a patch lead from the router going to a Linksys Wireless G access point IP 192.168.1.245 with DHCP disabled.
I can connect to the access point from the laptop, but how do I get the... (1 Reply)
At the moment, I have three computers at home. I want to use boardband for my three computers. But I don't want to use network at home. I have been looking for a product which call OriNoCo USB Cilent. How do I connect to the internet with my computer??
If I post this in a wrong place, please... (0 Replies)
Discussion started by: him
LEARN ABOUT FREEBSD
URTW(4) BSD Kernel Interfaces Manual URTW(4)NAME
urtw -- Realtek RTL8187B/L USB IEEE 802.11b/g wireless network device
To compile this driver into the kernel, place the following lines in your kernel configuration file:
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
The urtw driver supports USB 802.11b/g wireless adapters based on the Realtek RTL8187B/L.
urtw supports station and monitor mode operation. Only one virtual interface may be configured at any time. For more information on config-
uring this device, see ifconfig(8).
The urtw driver supports Realtek RTL8187B/L based wireless network devices, including:
Card Radio Bus
Belkin F5D7050E RTL8225 USB
Linksys WUSB54GCv2 RTL8225 USB
Netgear WG111v2 RTL8225 USB
Netgear WG111v3 RTL8225 USB
Safehome WLG-1500SMA5 RTL8225 USB
Shuttle XPC Accessory PN20 RTL8225 USB
Sitecom WL168v1 RTL8225 USB
Sitecom WL168v4 RTL8225 USB
SureCom EP-9001-g(2A) RTL8225 USB
TRENDnet TEW-424UB V3.xR RTL8225 USB
Join an existing BSS network (i.e., connect to an access point):
ifconfig wlan create wlandev urtw0 inet 192.168.0.20
Join a specific BSS network with network name ``my_net'':
ifconfig wlan create wlandev urtw0 ssid my_net up
Join a specific BSS network with 64-bit WEP encryption:
ifconfig wlan create wlandev urtw0 ssid my_net
wepmode on wepkey 0x1234567890 weptxkey 1 up
SEE ALSO intro(4), netintro(4), usb(4), wlan(4), wlan_ccmp(4), wlan_tkip(4), wlan_wep(4), ifconfig(8), wpa_supplicant(8)
The urtw device driver first appeared in FreeBSD 8.0.
The urtw driver was written by Weongyo Jeong <weongyo@FreeBSD.org>.
BSD October 17, 2009 BSD