Could not connect to wireless network


 
Thread Tools Search this Thread
Operating Systems Linux Ubuntu Could not connect to wireless network
# 1  
Old 08-10-2017
Could not connect to wireless network

I run lubuntu from usb (try lubuntu, it's not install on my pc )
And i try to connect to network
I see the network name
And i put the pass
But it's not connect..

I tried to open hot spot on my phone and try to connect and it's not connect

I have edumax n150
Try to install new driver - didn't help

Anyone know the problem?

Sent from my SM-J5108 using Tapatalk
Login or Register to Ask a Question

Previous Thread | Next Thread

8 More Discussions You Might Find Interesting

1. Android

Problem with wireless network

Good day, everybody! I have a mobile phone (LG Optimus L5) with Android 4.0.3 and a tablet (PocketBook SurfPad 2) with Android 4.1.1 and I have problem with wireless network on these devices. Laptops don't have such problem. My wireless network organisation is a modem connected with an access point... (11 Replies)
Discussion started by: qzxcvbnm
11 Replies

2. Red Hat

Unable to connect Wireless

I have managed to install Broadcom BCM43228 Wireless adapter on a laptop running CentOS 5.9 using instructions at: wiki.centos.org/HowTos/Laptops/Wireless/Broadcom I had the problem "Error for wireless request "Set Encode" (8B2A): SET failed on device... mentioned on the same page and solved... (0 Replies)
Discussion started by: cooltoad
0 Replies

3. Ubuntu

Wireless network not working

Hi, I am a new to Ubuntu linux and trying to learn it. I am using ubuntu 10.04. I am getting problem in setting my wireless network. I set it up properly and was working fine. But suddenly it stopped working, though the wireless icon saying that it is connected, but can't load any page. I... (2 Replies)
Discussion started by: linux_learner
2 Replies

4. Solaris

how to connect to wireless from virtual box

hi everyone... this is my first post here please help me with this..as iam new to solaris i have installed solaris 10 on virtual box.. and am not able to connect to the internet .. is there anyway i can get connect to the net.. please help me step by step if possible... thanks in... (1 Reply)
Discussion started by: yrajendergoud
1 Replies

5. IP Networking

my wireless usb adapter connect to net but the signal is very weak

i have wireless usb adapter rtl8187 from micromax company my proplem is the signal is very weak and i cannot open website can i increase the signal ? iwconfig lo no wireless extensions. eth0 no wireless extensions. wmaster0 no wireless extensions. wlan0... (5 Replies)
Discussion started by: rsd220
5 Replies

6. UNIX for Dummies Questions & Answers

solaris 10 wireless network setup

I installed solaris 10 x86 on my dell laptop on a partition alongside windows xp. I am able to connect to the internet in xp with both my ethernet local area connection as well as through my wireless network card. But, however i do not have clue as to how to go about it in solaris. i did not... (0 Replies)
Discussion started by: stakes20
0 Replies

7. IP Networking

Wireless-G network

Hi, I have a laptop with a Linksys Wireless G PCMCIA card and a cable connection goin into a router and then a patch lead from the router going to a Linksys Wireless G access point IP 192.168.1.245 with DHCP disabled. I can connect to the access point from the laptop, but how do I get the... (1 Reply)
Discussion started by: perleo
1 Replies

8. Cybersecurity

Wireless Network

At the moment, I have three computers at home. I want to use boardband for my three computers. But I don't want to use network at home. I have been looking for a product which call OriNoCo USB Cilent. How do I connect to the internet with my computer?? If I post this in a wrong place, please... (0 Replies)
Discussion started by: him
0 Replies
Login or Register to Ask a Question
URTW(4) 						   BSD Kernel Interfaces Manual 						   URTW(4)

NAME
urtw -- Realtek RTL8187B/L USB IEEE 802.11b/g wireless network device SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device ehci device uhci device ohci device usb device urtw device wlan Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): if_urtw_load="YES" DESCRIPTION
The urtw driver supports USB 802.11b/g wireless adapters based on the Realtek RTL8187B/L. urtw supports station and monitor mode operation. Only one virtual interface may be configured at any time. For more information on config- uring this device, see ifconfig(8). HARDWARE
The urtw driver supports Realtek RTL8187B/L based wireless network devices, including: Card Radio Bus Belkin F5D7050E RTL8225 USB Linksys WUSB54GCv2 RTL8225 USB Netgear WG111v2 RTL8225 USB Netgear WG111v3 RTL8225 USB Safehome WLG-1500SMA5 RTL8225 USB Shuttle XPC Accessory PN20 RTL8225 USB Sitecom WL168v1 RTL8225 USB Sitecom WL168v4 RTL8225 USB SureCom EP-9001-g(2A) RTL8225 USB TRENDnet TEW-424UB V3.xR RTL8225 USB EXAMPLES
Join an existing BSS network (i.e., connect to an access point): ifconfig wlan create wlandev urtw0 inet 192.168.0.20 netmask 0xffffff00 Join a specific BSS network with network name ``my_net'': ifconfig wlan create wlandev urtw0 ssid my_net up Join a specific BSS network with 64-bit WEP encryption: ifconfig wlan create wlandev urtw0 ssid my_net wepmode on wepkey 0x1234567890 weptxkey 1 up SEE ALSO
intro(4), netintro(4), usb(4), wlan(4), wlan_ccmp(4), wlan_tkip(4), wlan_wep(4), ifconfig(8), wpa_supplicant(8) Realtek, http://www.realtek.com.tw. HISTORY
The urtw device driver first appeared in FreeBSD 8.0. AUTHORS
The urtw driver was written by Weongyo Jeong <weongyo@FreeBSD.org>. BSD
October 17, 2009 BSD