Login or Register to Ask a Question and Join Our Community


Ubuntu

Ubuntu Install on Sun Fire X4100 network issues

Login to Discuss or Reply to this Discussion in Our Community

 
Thread Tools Search this Thread
Operating Systems Linux Ubuntu Ubuntu Install on Sun Fire X4100 network issues
# 1  
Old 03-15-2013
Ubuntu Install on Sun Fire X4100 network issues
Hi

I have two Sun Fire X4100 machines with Ubuntu 12.04 installed on them.
I am able to configure the Net Mgt port with an IP address and access the ILOM from the browser. I can also boot the Ubuntu installed and redirect the output.

The issue i have is that when i configure the network interface(NET0) from Ubuntu and connect an ethernet cable to it i am unable to reach it via ping or ssh. I am also unable to ping out from it. I can confirm that all the network parameters(IP address,Netmask,gateway) are set correctly. And the NET0 interface is connected to the same switch the Net Mgt is connected to. I can ssh and ping the Net Mgt but not the NET0 interface.

I will really appreciate your help. Thanks
Login or Register to Ask a Question

Previous Thread | Next Thread

9 More Discussions You Might Find Interesting

1. Solaris

Sun fire x2270

Hello, I have purchaced an old SUn fire x2270 server . I wanted to make ILOM upgrade to the latest version of software : ILOM 3.0.9.18.a r126592 BIOS vers. 2.09 Server 2.2.3 (10-Aug-2018) Because my version is very outdated. But i can't download the updatebecause it's require... (4 Replies)
Discussion started by: LouisLakoute
4 Replies

2. Hardware

Multi-bit ECC Error on X4100 M2 Server Sun Fire

I have a problem, I have been installing Redhat Interprise Linux on X4100 M2 Server, when system is reboot after install, the server is restart (reboot) again (alias unlimited). The bios system show message error "Multi-bit ECC Error" and "bank interleave requested but not enable" I have... (5 Replies)
Discussion started by: hhaswan
5 Replies

3. Solaris

Sun Fire 4800 is not powering-on

I switched on the power to the server. But, the server did not power on i.e., none of the 3 LEDs on the front panel is lighted. (Power supplies are showing only amber LEDs with "Ready to remove" sign). I tried to turn on the power supplies via System Controller menu (platform shell), but it... (6 Replies)
Discussion started by: solind
6 Replies

4. Hardware

Sun X4100 graphics

Hello all. I have a requirement to install a aftermarket video card in the server, can you advise what fits? or if there is a sun riser part which convers the PCIx slot to PCIe The unit is a standard x4100 with PCIx slots, not an M2 with the PCIe slots. thanks (4 Replies)
Discussion started by: petebarchetta
4 Replies

5. Hardware

sun x4100 M2 processors

hi please how to know that a sun x4100 m2 server has one or two processors installed ?? the OS installed on this server is windows 2003 Enterprise Edition. thanks (2 Replies)
Discussion started by: bahjatm
2 Replies

6. Solaris

Does the Sun fire x4100 support HVM?

I have looked all over the bios configuration to enable hardware virtualization and found nothing. Could someone tell if this server support it and if so where I go to enable that feature. By the way this is a x86 server. (0 Replies)
Discussion started by: jsandova
0 Replies

7. Solaris

Sun Fire 280R Sun Solaris CRT/Monitor requirements

I am new to Sun. I brought Sun Fire 280R to practice UNIX. What are the requirements for the monitor/CRT? Will it burn out old non-Sun CRTs? Does it need LCD monitor? Thanks. (3 Replies)
Discussion started by: bramptonmt
3 Replies

8. UNIX for Dummies Questions & Answers

Sun Fire 280R

Hello all, I'm lost and can't figure this problem out. I have a Sun fire 280R running Solaris 8. Everything was working great. I have one drive in bay 1(not 0). But when I reboot the system it trys to open files in /dev/rdsk/c1t1d0s0. Should it have been opeing /dev/rdsk/c1t0d0s0, the... (4 Replies)
Discussion started by: larryase
4 Replies

9. UNIX for Advanced & Expert Users

Sun Fire v1280 is crashing

I still haven't got an answer to this question... Excerpt from My SysAd Blog A colleague of mine is having a problem with a Sun Fire v1280 server crashing. He tried Googling for the error message in red but hasn't found anything yet. Your insights would be greatly appreciated. "cannot... (2 Replies)
Discussion started by: esofthub
2 Replies
Login or Register to Ask a Question

LEARN ABOUT XFREE86

what-patch

WHAT-PATCH(1)						      General Commands Manual						     WHAT-PATCH(1)

NAME

       what-patch - detect which patch system a Debian package uses

SYNOPSIS

       what-patch [options]

DESCRIPTION

       what-patch examines the debian/rules file to determine which patch system the Debian package is using.

       what-patch should be run from the root directory of the Debian source package.

OPTIONS

       Listed below are the command line options for what-patch:

       -h, --help
	      Display a help message and exit.

       -v     Enable verbose mode.  This will include the listing of any files modified outside or the debian/ directory and report any additional
	      details about the patch system if available.

AUTHORS

       what-patch was written by Kees Cook <kees@ubuntu.com>, Siegfried-A. Gevatter <rainct@ubuntu.com>, and  Daniel  Hahler  <ubuntu@thequod.de>,
       among others.  This manual page was written by Jonathan Patrick Davies <jpds@ubuntu.com>.

       Both are released under the GNU General Public License, version 3 or later.

SEE ALSO

       The Ubuntu MOTU team has some documentation about patch systems at the Ubuntu wiki: https://wiki.ubuntu.com/PackagingGuide/PatchSystems

       cdbs-edit-patch(1), dbs-edit-patch(1), dpatch-edit-patch(1)

DEBIAN
								 Debian Utilities						     WHAT-PATCH(1)