ufsdump

native(5)						Standards, Environments, and Macros						 native(5)

NAME

       native - native branded zone

DESCRIPTION

       The  native  brand uses the branded zones framework described in brands(5) to run zones installed with the same software as is installed in
       the global zone. The system software must always be in sync with the global zone when using a native brand.

SUB-COMMANDS
       The following native brand-specific subcommand options are supported in zoneadm(1M).

       attach [-u] [-b patchid]...

	   For native zones, zoneadm checks package and patch levels on the  machine to which the zone is to be attached. If the  packages/patches
	   that  the  zone  depends on from the global zone are different (have different revision numbers) from the dependent packages/patches on
	   the source machine, zoneadm reports these conflicts and does not perform the attach. If the destination system has only newer dependent
	   packages/patches  (higher  revision	numbers) than those on the source system, you can use the -u option to update the attached zone to
	   match the -revision packages and patches that exist on the new system. With -u, as in the default behavior, zoneadm does not perform an
	   attach if outdated packages/patches are found on the target system.

	   For	native	zones,	one  or more -b options can be used to specify a patch ID for a patch installed in the zone. These patches will be
	   backed out before the zone is attached or, if -u was also specified, updated.

       install [-a archive] | [-d path] [-p] [-s] [-u] [-v] [-b patchid]...

	   The native brand installer supports installing the zone from either the software already installed on the system or from an image of an
	   installed system running the same release.  This can be a full flash archive (see flash_archive(4)) or a cpio(1) or pax(1) "xustar" ar-
	   chive.  The cpio archive be compressed with gzip or bzip2.  The image can also be a level 0 ufsdump(1M), a path to the top-level  of  a
	   system's root tree, or a pre-existing zone path.

	   With no options the zone is installed using same software as is running the global zone.

	   To install the zone from a system image either the -a or -d is required.  Either the -u or -p option is also required in this case.

	   -a archive

	       The path to a flash_archive(4), cpio(1), or pax(1) "xustar" archive, or a level0 ufsdump(1M), of an installed system. cpio archives
	       may be compressed using gzip or bzip2.

	   -b patchid

	       One or more -b options can be used to specify a patch ID for a patch installed in the system image. These patches  will	be  backed
	       out during the installation process.

	   -d path

	       The  path  to  the root directory of an installed system. If path is a hyphen (-), the zonepath is presumed to be already populated
	       with the system image.

	   -p

	       Preserve the system configuration after installing the zone.

	   -s

	       Install silently.

	   -u

	       Run sys-unconfig(1M) on the zone after installing it.

	   -v

	       Verbose output from the install process.

ATTRIBUTES

       See attributes(5) for a description of the following attributes:

       +-----------------------------+-----------------------------+
       |      ATTRIBUTE TYPE	     |	    ATTRIBUTE VALUE	   |
       +-----------------------------+-----------------------------+
       |Availability		     |SUNWzoneu 		   |
       +-----------------------------+-----------------------------+
       |Interface Stability	     |Uncommitted		   |
       +-----------------------------+-----------------------------+

SEE ALSO

       cpio(1),  pax(1),  zlogin(1),  zonename(1),  sys-unconfig(1M),  ufsdump(1M),  zoneadm(1M),  zonecfg(1M),  flash_archive(4),  attributes(5),
       brands(5), privileges(5), zones(5), lx_systrace(7D)

SunOS 5.11							    13 Feb 2009 							 native(5)