Can't see Netapp LUN on Solaris using LPFC after reboot.

9 More Discussions You Might Find Interesting

1. Linux

Identify newly attached LUN from NetApp

Hi I need to identify a newly attached LUN from NetApp on a linuxserver running uname -o GNU/Linux I have first run the df -h and got the following: df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/vg_outsystemdb-lv_root 50G 2.7G 45G ...

2. Solaris

How to mount a NetApp snapshoot to a Solaris server?

Hi I have NetApp lun, that was mounted on server as a file system that failed, and that server is no longer in use, but I would like to use that file system on another server. The NetApp Admin, told me he can present that lun to my other system, but my problem is how to mount it? Because that...

3. Solaris

Restore of Netapp FC lun targets used as the disks for a zpool with exported zfs file systems

So, We have a Netapp storage solution. We have Sparc T4-4s running with LDOMS and client zones in the LDOMS, We are using FC for storage comms. So here's the basic setup FC luns are exported to the primary on the Sparc box. using LDM they are then exported to the LDOM using vdisk. at the...

4. AIX

Netapp iscsi lun

Hi, I have aix 6.1 box. I want to configure iscsi luns from netapp storage. I tried in google but not getting proper solution for that. i m not getting the proper iqn name. Please share me the steps to complete this requirements. Thanks in advance.

5. UNIX for Advanced & Expert Users

Removing EMC LUN from Solaris 10 host without a reboot

I have seen a few threads / posts on the forum's but nothing specific to what Iam after. So Iam hoping you can help. Issue : Iam hoping to remove unused emc luns from my solaris servers , T2000 (5.10 Generic_142900-02). I have a list of the process I have followed for the removal of the luns....

6. Solaris

Solaris 10 / NetApp volumes - Forbidden: You don't have permission to access...

Hi all We have a couple of solaris zones running a jboss app in a cluster. Each zone has a shared netapp volume mounted to /app/xxx with everything under that subdir apart from jboss which is local to each zone in /app/jboss-3.2.5 There is a symlink in /app/xxx/jboss-3.2.5 which points to...

7. Solaris

Connect Solaris 10 to NetApp filer using Emulex single port HBAs.

Hi, I'm connecting a Solaris 10 server to a Netapp filer with two single port Emulex (Sun StorageTek PCI-X Enterprise 4GB FC HBA) HBAs. After physically installing both these HBAs what do I ned to do within Solaris 10 to enable them and configure them with persistent bindings. Do I need...

8. Solaris

Netapp filer LUN Resize. Commands to run on Solaris afterwards.

Hi, I need to increase a veritas filesystem I have currently mounted on a Solaris 10 server. We can resize the LUN on the NetApp filer no problem. What I need to know is what do I do next on the Solaris 10 server I have so that it will see the increase in size. Do I run 'devfsadm' to...

9. Solaris

Use DFM Netapp 3.01 R1 on Solaris 8

I have this problem when i integrate a new san switch in DFM 3.01 R1 : dfm fcswitch add switchname1 Error: Host switchname2 (11197) already exists. switchname2 is a similar san switch but in another fabric, switchname2 is already integrated in DFM database. Bests Regards Olivier

LEARN ABOUT ULTRIX

reboot

reboot(8)						      System Manager's Manual							 reboot(8)

Name
       reboot - automatic reboot procedures

Syntax
       /etc/reboot [ -n ] [ -q ]

Description
       The  ULTRIX  system is booted by loading a kernel image, usually into memory at location zero and transferring to zero.	Because the system
       is not reenterable, the kernel image must be read in from disk each time the system is bootstrapped.

       When the reboot of a running system is desired, is normally used.  If there are no users, can be used.  The command causes the disks to	be
       synced,	and  then  a multiuser reboot is initiated.  The system is booted and an automatic disk check is performed.  If the procedure suc-
       ceeds, the system is then brought up for the users.

       The system will reboot itself after a power failure or after a crash, provided auto-restart is enabled on your system.  A consistency check
       of the file systems will be performed and, unless the check fails, the system will resume multiuser operations.

Options
       -n   Prevents the disks from being synced.

       -q   Reboots quickly and ungracefully, without shutting down running processes first.

Files
       System code

See Also
       crash(8v), fsck(8), halt(8), init(8), newfs(8), rc(8), shutdown(8)

																	 reboot(8)

Solaris