10 More Discussions You Might Find Interesting
1. Solaris
Installing Solaris x86 using jumpstart does not set the hostname for the target. Any idea where do we need to specify hostname to be set for jumpstart installation. (1 Reply)
Discussion started by: hemalsid
1 Replies
2. Solaris
I am trying to install Solaris x86 using the Jumpstart server. I run the add_install_client command with appropriate options, and reboot my x86 Target box. The installation starts fine and unattended. After the installation completes and the target goes for a re-boot, it does not boot from the HDD... (9 Replies)
Discussion started by: hemalsid
9 Replies
3. Solaris
I have a jumpstart client that is not requesting the tftp boot file. The rarp function is working, hostname and ip are set ok, but it hangs after that.
tcpdump output:
jumpstart-server:/var/lib/tftpboot# tcpdump -i eth1
tcpdump: verbose output suppressed, use -v or -vv for full protocol... (6 Replies)
Discussion started by: skitch
6 Replies
4. Solaris
client boots fine, it gets the ip 192.168.0.10 and the bootfile. Then there is :
SunOS 5.10 Version Generic_141445-09 32-bit"
...
Configuring devices.
Custom JumpStart
Reading ZFS config: done
Setting up Java. Please wait ...
NOTE: Not enough memory for graphical installation. Graphical... (4 Replies)
Discussion started by: TomSu
4 Replies
5. Solaris
Hi friends ,
i have on ultra 10 Sparc machine . Due to some problem my OS is fully corrupted , so i am planning to install again but my problem is the cd drive in Ultra 10 machine is not working.
Now i am planning to use Jumpstart installation method to install my server.
But i... (4 Replies)
Discussion started by: vr_mari
4 Replies
6. Solaris
Hi All,
Is there a possible way to fully automate Solaris x86 jumpstart or make the x86 jumpstart unattended?
I'm currently checking the possible options on how can I do the x86 jumpstart to be kicked off during midnight.
We have an automated jumpstart (start to run from midnight) for... (2 Replies)
Discussion started by: racbern
2 Replies
7. Solaris
Can I use a Jumpstart enviroment on x86 to install a sparc64 client?
The idea is to install Solaris in an virtual environment (Sun Virtual Box) running on a pc (AMD), configure a Jumpstart server, and have a SUN Ultra 60 (sparc64) installed via the Jumpstart server.
The SUN has no cdrom... (4 Replies)
Discussion started by: eldiablo
4 Replies
8. Solaris
Does anyone know how to Jumpstart a Solaris 10 x86 system without the GUI?
I would like to keep the Jumpstart and/or Flash Archive install in a console text mode if possible but I've not had much luck finding instructions. I'm guessing this is going to be accomplished from the grub menu with a... (5 Replies)
Discussion started by: alias.256
5 Replies
9. Solaris
I need a little help figuring out why my custom jumpstart network installation is dumping me to a manual install.
I am trying to install Solaris 10 (unattended) over the wire from my jumpstart server to an HP Proliant DL380 server but I'm having difficulties with the unattended part.
So, what... (2 Replies)
Discussion started by: alias.256
2 Replies
10. Solaris
Hi
I just configured a jumpstart server for x86 and sparc clients. I don't use a dhcp server, so I configured /etc/ethers and did add_install_client to update /etc/bootparams. The sparc installation ist working, but the x86 installation stops after CD1 was successfully installed.
What I did:
I... (2 Replies)
Discussion started by: Jay_Fisi
2 Replies