Connect Solaris 10 to NetApp filer using Emulex single port HBAs.
Hi,
I'm connecting a Solaris 10 server to a Netapp filer with two single port Emulex (Sun StorageTek PCI-X Enterprise 4GB FC HBA) HBAs. After physically installing both these HBAs what do I ned to do within Solaris 10 to enable them and configure them with persistent bindings.
Do I need to install that 'lputil' application in order to configure persistent bindings? Also how do I configure multipathing? Please let me know.
Thanks for your reply. I have worked through the documentation which was really helpful. My problem now is that lptuil does not recognise the two HBAs I have installed. When I run the lputil utility it returns nothing. My system does see the devices. I have run the utility /opt/EMLXemlxu/bin/emlxdrv. Below is what it sees. Because both the HBA's are LP11000-S, I cannot bind the lpfc driver to that device. They can only use the emulex driver.
lpfc fd00 no no no LP11000 and LP11002
lpfc fe00 no no no LPe11000,LPe11002 and LPe11004
emlxs fc10 yes no yes LP11000-S and LP11002-S (emlxs only)
emlxdrv> set_lpfc fc10
ERROR: lpfc cannot bind to a Sun device (fc10).
I now need to know how to configure this HBA (LP11000-S) for persistent bindings to a NetApp filer? Any ideas?
Lets see what we got first so we can help you out a little more
issue a `modinfo` and let see what drivers the kernel is trying to use.
issue a `prtconf` and this should give us if the hba is sd or ssd (not at work so i can't be 100% sure. if its not the right command, i can post a bit later with what i'm looking for).
my thoughts are that you are trying to bind a lpfc to an sfs (emlx) driver. so issue a:
i maybe wrong but i think you can also issue
and this will bind emlx sfs drivers (not native leadville) to all sun branded devices. i believe the '-s' at the end of LP11000-S means its a sun-branded device.
see if this helps you. also, i think there will be a situation were when you view the physical device path, you will see lpfc even though you have loaded emlx drivers. however, there are two ways of changing this. one is at the OBP and the other can be done without restarting the box. but if/when you get there... lets figure that out.
the emulex lputil (including hbanyware util) is only for lpfc devices. in order for you to work with the sfs drivers you will use all the emulex provided utils
so there are two drivers:
1. emulex sfs fca (emlxs) <--- this is leadville driver (which i wrote wrongly in the other post. sorry about that!!!)
2. emulex lpfc
sun-branded emulex hbas are only supported by SFS drivers only. lpfc won't load.
so, by your output, it looks as if all hbas are picking up the sfs driver which is good.
i believe you need to use cfgadm to configure this and then update your /etc/vfstab with the ssd pathname.
The chassis config is right... this blade can boot to VMware ESXi and see HBAs and LUNs. Solaris isn't seeing the HBAs at all... luxadm probe returns ERROR: No Fibre Channel Adapters found.
fcinfo hba-port -l returns No Adapters Found.
prtdiag -v gets me:
==== Upgradeable Slots... (3 Replies)
Hi
I have NetApp lun, that was mounted on server as a file system that failed, and that server is no longer in use, but I would like to use that file system on another server. The NetApp Admin, told me he can present that lun to my other system, but my problem is how to mount it? Because that... (8 Replies)
What command can I use to find out details about a netapp filer.
I have a directory that is a filer i would like to know details about the source host/folder that it points to.
Thanks. (2 Replies)
Hi all
We have a couple of solaris zones running a jboss app in a cluster. Each zone has a shared netapp volume mounted to /app/xxx with everything under that subdir apart from jboss which is local to each zone in /app/jboss-3.2.5
There is a symlink in /app/xxx/jboss-3.2.5 which points to... (0 Replies)
Hi,
I need to increase a veritas filesystem I have currently mounted on a Solaris 10 server. We can resize the LUN on the NetApp filer no problem. What I need to know is what do I do next on the Solaris 10 server I have so that it will see the increase in size. Do I run 'devfsadm' to... (3 Replies)
Hello!
I'm having problems to install Emulex fibrechannel card drivers to a HP DL580 G5 running Solaris 10 x86_64. Any of you guys had this problem or knows the answer? =)
cfgadm gives me the following info, which seems to say that it is ok?
But the card has'nt logged into the switch... (0 Replies)
Hello,
I am new on solaris. We will connect our sun solaris system to the SAN and add 2 Emulex card on the system (solaris 9).
Who have already done this and can give me the procedure to follow ?
driver to install
multipath
etc...
Thanks in advance
Emmanuel (1 Reply)
I have this problem when i integrate a new san switch in DFM 3.01 R1 :
dfm fcswitch add switchname1
Error: Host switchname2 (11197) already exists.
switchname2 is a similar san switch but in another fabric, switchname2 is already integrated in DFM database.
Bests Regards
Olivier (2 Replies)