Login or Register to Ask a Question and Join Our Community


Solaris

assigning ip to second interface

Login to Discuss or Reply to this Discussion in Our Community

 
Thread Tools Search this Thread
Operating Systems Solaris assigning ip to second interface
# 8  
Old 02-06-2008
PHP ip to Second Interface
I also run the
grep net/etc/path_to_inst

it gives the following output.

/pci@8,700000/network@,1" 0 "eri"
# 9  
Old 02-06-2008
PHP Rep: Ip to Second interface
I also run the following command
grep eri /etc/path_to_isnt

it gives the follwoing output

"/pci@8,700000/ebus@5/serial@1,400000" 0 "se"
"/pci@8,700000/networks@5,1"0 "eri "

grep qfe /etc/path_to_inst

then no output is shown
# 10  
Old 02-06-2008
the r280 has only ONE internal ip interface? the card with a second nic is the "rsc" card and can not be used as nic from os! if there is NO networkcard in a pci slot you only have ONE nic! and this is eri0...

greets,
DN2
# 11  
Old 02-07-2008
PHP assigning ip to second interface
so what i should do now. Either I should installed a external inerface card to it or any other method to use any other slot as nic.
# 12  
Old 02-07-2008
you can assign a second ip to your internal interface... or you have to install a new network card to add more interfaces to your mashine.
Login or Register to Ask a Question

Previous Thread | Next Thread

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Assigning ipv6 to bonding interface - getting old as well as changed ipv6 in ifconfig output

Hi, I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies

2. UNIX for Advanced & Expert Users

C program to detect duplicate ip address if any after assigning ip address to ethernet interface

Hi , Could someone let me know how to detect duplicate ip address after assigning ip address to ethernet interface using c program (3 Replies)
Discussion started by: Gopi Krishna P
3 Replies

3. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies

4. Shell Programming and Scripting

Assigning variables

i have variables RECIPIENTS_DEVL,RECIPIENTS_UACC,RECIPIENTS_PROD i have a case statement to get the phase variable: case ${WMD_UPHASE1} in u) WMD_UPHASE4=UACC;; i) WMD_UPHASE4=DEVL;; p) WMD_UPHASE4=PROD;; d) WMD_UPHASE4=DEVL;; *) WMD_UPHASE4=DEVL;; esac I am unable to... (3 Replies)
Discussion started by: Arun Mishra
3 Replies

5. IP Networking

Need a bridge from an ethernet interface to a serial interface

This is my situation DOS pc serial cable (sl0) Linux Pc eth1 192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router) I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface. ... (3 Replies)
Discussion started by: mghis
3 Replies

6. SCO

Change SCO - GUI or Desktop interface to DOS based interface

Hi all I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface? If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies

7. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies

8. HP-UX

Assigning IP's

hi all, i want to know where i can add and IP address so when i do a "w", i can see what IP is assigned to which tty? i know in tru64 you just added an entry to /etc/hosts. this does not seem to be the case with hpux. thanks (12 Replies)
Discussion started by: macgre_r
12 Replies

9. UNIX for Dummies Questions & Answers

assigning variables

Before I even attempt this, is it possible to grep for a pattern, maybe a partial sentence like "go to page 3", assign that to a variable and then use awk or something to pull out the 3 and assign it to a variable? So first I would have Gotopg = "go to page 3" then page = 3 (9 Replies)
Discussion started by: k@ssidy
9 Replies
Login or Register to Ask a Question