10 More Discussions You Might Find Interesting
1. Solaris
Hello all, thanks for reading my question:
So I've been a Unix/Linux SysAdmin for a couple years, and I'm a bit over my head running solo, trying to set up LDoms using Oracle VM Server 3.1 for SPARC. I've been very careful, and things have gone well up until the point I try to access the new... (9 Replies)
Discussion started by: Lyxix
9 Replies
2. Solaris
Hi,
I am getting following service error on one of the sparc servers running solaris 10 -
Code :
$ svcs -a | grep "maintenance"
maintenance Nov_08 svc:/application/management/sma:default
$ svcs -xv
svc:/application/management/sma:default (net-snmp SNMP daemon)
State: maintenance... (8 Replies)
Discussion started by: sunadmin
8 Replies
3. SuSE
Hello,
Does any one know any command which reboot the system and select as boot device the network.
I give bootnet to many servers at once and i want to avoid opening ILOM and select as boot device the network.
Can i do it by just executing a command?
Thanks in advance (2 Replies)
Discussion started by: @dagio
2 Replies
4. Solaris
Hi all!
I've a machine - SunFire V890, it've been failed by OS error for 2 weeks ago, and now, I must reinstall OS (Solaris 10 2009), the progress was successful, but when I reboot, it displayed the error like :
Error -256: Last trap memory ... access aligned
Error -256: Last trap memory... (1 Reply)
Discussion started by: trantuananh24hg
1 Replies
5. Solaris
Hi Gurus
I would like to know whether break command always work well means take the system to ok> prompt. Its depend upon sever model also. As I am facing problem when ever my system ( Sunfire V890 ) having Solaris 10 OS & oracle RAC on it goes to hang state then I run the break command from... (6 Replies)
Discussion started by: girish.batra
6 Replies
6. SCO
Hi .. can anyone help with this pleeaasse ..
I have a Sco Unixware 7.1.0 server which has been running fine for nearly 10 years ... we have not had to do any os changes for several years.
We tend to reboot it about once a month just to keep everthing clean!
My issue is that we have just... (7 Replies)
Discussion started by: DickTutton
7 Replies
7. Solaris
hi expert,
i had do sys-unconfig for my v890 sparc and had config for eri0 network interface and hostname but after the server bring up i got this error messages :
NIS domainname is www.USSDGmdn-4.com
starting rpc services: rpcbind keyserv done.
Setting netmask of eri0 to 255.255.255.0... (5 Replies)
Discussion started by: bucci
5 Replies
8. Solaris
hi experts,
i have some problem with my server v890, i had config the network with ce0,ce1 and eri0 but after reboot the server have this error messages display :
WARNING: ce0: fault detected external to device; service degraded
WARNING: ce0: xcvr addr:0x01 - link down
configuring IPv4... (2 Replies)
Discussion started by: bucci
2 Replies
9. Solaris
hi expert,
sorry i'm new in solaris system, need more advice and help :)
i'm confusing with mirroring disk at my sparc v890 solaris 8, i have 6 harddisk which the structure shown below :
format :
AVAILABLE DISK SELECTIONS:
0. c1t0d0 <SUN146G cyl 14087 alt 2 hd 24 sec 848>
... (4 Replies)
Discussion started by: bucci
4 Replies
10. Solaris
I have 4 V440 servers running Solaris 9. I have their interfaces configured (ce0) and have connectivity to our network. However, after reboot,...the connectivity is lost although the interface shows that its still up after an ifconfig -a.
Only after I reconfigure the interface do I restore... (19 Replies)
Discussion started by: StorageGuy
19 Replies