Help with Reviving a NETRA240 Pls?


 
Thread Tools Search this Thread
Operating Systems Solaris Help with Reviving a NETRA240 Pls?
# 1  
Old 11-21-2018
Help with Reviving a NETRA240 Pls?

Hi Everybody,

Hope everybody is having fun with their Solaris installations and not pulling out too much of whatever hair they have left so far. Smilie

Just for sport, I bought an old Netra 240 used by Northern Telecom Turkish subsidiary Netas here in Turkey. My hope is to turn this into an ugly workstation for playing with some old CAD software. At worst, I like to install some Linux or BSD on it, if I can get it up. My server I mean. Smilie

I do not know the last IP numbers used for it. And cannot get a response from serial management port. Here are the steps I have taken so far with some pics.

1- Connected two 48V DC power supplies to its internal power makers. They are both on seem to work fine. The cases say they produce 13V, 3.3V etc. However I just measure 4,9V on all pins of both supplies. Maybe the case sticker is outdated. They do seem to do their job as will be seen.

Help with Reviving a NETRA240 Pls?-netra_001jpg


2- When power is first supplied management ethernet port link light comes on when connected to a switch. However the critical light on front also does. When the card at front is taken out the back error light with wrench sign comes on. There is no response from the serial port.

Help with Reviving a NETRA240 Pls?-netra_002jpg


3- After turning the little blue knob at front half a turn either way, the on switch next to it brings up main power and the big air fan starts working with a big whoosh. The hard disk power light turns on temporarily then goes out. DVD has no lights on. Its button is unresponsive. Does not seem to have power. But its in place firmly. I can take it out and insert back. Hard Disk also comes in and out securely. Regular ethernet ports start lighting up after the main fan works. However the "critical" light at front panel is still on.

Help with Reviving a NETRA240 Pls?-netra_003jpg


4- I tried Putty, TeraTerm, MobaXTerm, and BB ComTest programs to get a response from the serial port to no avail. It seems deaf, unresponsive. I did check my serial cable with TX-RX pin short. However when Netra is powered on with terminal emulator open, a single character came up into terminal which might be indicating serial port is electrically excited during start up, hence connected to something.

MY QUESTION is to people with actual real Sun Server experience. What should be checked and tried in these situations? What would you do? What compartment inside the case should I dismantle? Should I try to send or broadcast a Wake-On-LAN signal packet? Is there a default local LAN IP address that these servers are assigned with? Is this thing alive yet? If yes, how can I start communicating? etc. etc.

This has been a long time dream of mine to be able to tap into a real sun sparc server. Thanks to their sexy Frog Design boxes and ever nimble marketing, these clunky boxes has been every engineer's wettest dream for a long time. I have to see what the buzz has been about these please. I want in! Smilie

Rest of my pictures are in the following message. Thanks for checking me out. Any ideas would truly be greatly appreciated!

Help with Reviving a NETRA240 Pls?-netra_005jpg


Help with Reviving a NETRA240 Pls?-netra_006jpg

Last edited by Neo; 12-03-2018 at 12:18 PM..
This User Gave Thanks to ozsavran For This Post:
# 2  
Old 11-21-2018
Rest Of Netra 240 Pictures

These are the rest of the pictures of my efforts on reviving the Netra.

Help with Reviving a NETRA240 Pls?-netra_007jpg


Help with Reviving a NETRA240 Pls?-netra_008jpg


Help with Reviving a NETRA240 Pls?-netra_009jpg


Help with Reviving a NETRA240 Pls?-netra_012jpg


Help with Reviving a NETRA240 Pls?-netra_014jpg
This User Gave Thanks to ozsavran For This Post:
# 3  
Old 11-21-2018
Firstly, thank you for providing such a comprehensive analysis of what you have tried. It helps us a lot to try and help you meaningfully.

Digest each of these statements I provide here and ask any questions if they're not clear enough.

The Netra 240 comprises (what can be regarded as two systems) the 'service processor' and the main processor.

The service processor (also known as SC) powers up as soon as volts are applied.

The main processor is under the control of the SC and may/or may not be programmed to power up automatically after the SC has started.

The SC reports its boot sequence via the SER-MGT port which is a RJ-45 interface!!!!! So you need a RJ-45 to DB-9 adapter which is a cable supplied in the box with a new machine. Do you have this? If not, a CISCO serial management cable (coloured light blue RJ-45 to DB-9) which CISCO network engineers use has the same pin-out so try and steal one of those.

Connect one end to the RJ-45 SER-MGT port (NOT the NET-MGT port) and the other end (DB-9) to an old laptop or the like with a serial DB9 port. Run a terminal emulator (default 9600-8-N-1) and then apply volts to the NETRA. If garbage appears on the terminal emulator, the baud rate is wrong; try a different speed.

Keep trying until it talks sense and then you are talking to the SC.

Last edited by hicksd8; 11-21-2018 at 04:22 PM..
These 4 Users Gave Thanks to hicksd8 For This Post:
# 4  
Old 11-21-2018
Wow! Thanks for such a speedy, comprehensive and very kind reply Mr. Hicks! I will try the new method, and get back to you. I do thank Mr. Corona as well for connecting my message to you. My sincere respects to you both for all your hard work, experience, and having the heart to share it all... This really is wonderful.
This User Gave Thanks to ozsavran For This Post:
# 5  
Old 11-21-2018
Hicksd8 found it all by himself. If you don't get an answer immediately, don't panic, just wait -- we have many knowledgeable people, but they aren't active 24 hours a day.
This User Gave Thanks to Corona688 For This Post:
# 6  
Old 11-26-2018
Netra240 SC is Talking! :)

My Good Man Hicksd8,

Using that light blue flat cable, and power it up after connecting worked its charm. Smilie It seems to pass all tests. I can turn off the "critical" light with "setalarm critical off", I can turn main power on with just "poweron" command. I start to see a little beauty from this heavy box. Can not boot an OS yet, but I will see the manual I downloaded. Here are the pics:

Help with Reviving a NETRA240 Pls?-wp_20181126_001jpg


Help with Reviving a NETRA240 Pls?-wp_20181126_003jpg


Help with Reviving a NETRA240 Pls?-wp_20181126_004jpg


Help with Reviving a NETRA240 Pls?-wp_20181126_007jpg
These 2 Users Gave Thanks to ozsavran For This Post:
# 7  
Old 11-26-2018
Well done!!!

If you have Solaris installation media (Solaris 8, 9, 10 or 11 SPARC version, of course) you can boot into single user with:

Code:
ok> boot cdrom -s

that will allow you to see that the hardware is capable of running Solaris.

If you:

Code:
ok> boot cdrom

it will boot and enter the Solaris install routine.

Your terminal emulator is connected to the SC after boot. If you want to talk to the main processor (after you've 'poweron' and installed Solaris) you can:

Code:
ok> console

to do that and get a login prompt.

When connected to main processor (Solaris) you can type

Code:
#.

to return to the SC.

There are a number of downloadable manuals on the web for the Netra 240 (service, install, admin, etc) so I suggest that you get your paws on those if you haven't already.

EDIT: As pointed out by Gull04 below, the Netra 240 cannot run Solaris 11.

Last edited by hicksd8; 11-27-2018 at 08:47 AM..
This User Gave Thanks to hicksd8 For This Post:
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. Solaris

NETRA240 in HLR CDMA Wireless Exchange... help is apreciated

Greetings, I hope my post finds you all OK, I have a Netra240 server in an HLR inside a wireless CDMA Exchange, it works as a Hard Disk Unit (HDU) as shown in Local Management Terminal (LMT) as show in the picture 1 attached. The power went down because of a power failure in main UPS, when... (2 Replies)
Discussion started by: Sharista
2 Replies

2. Homework & Coursework Questions

Help pls

How to find the ten most common words in a file (1 Reply)
Discussion started by: jass
1 Replies

3. UNIX for Dummies Questions & Answers

HELP PLs

I have this code: #!/bin/sh awk 'BEGIN NR == 2 repl = "PHI" $4 = repl print $0 'dryloop.txt and this code: #!/bin/sh sed -e '1s/\|$/\|COMID\|/g' -e 's/^087.*$/&PHI\|g' hl.dsldryloop > textdry.txt My code won't work. I want to change the COMID of lines starting with 087 . this is my... (15 Replies)
Discussion started by: arkhei
15 Replies

4. Shell Programming and Scripting

Pls Pls do help me

When i run this command, everything is ok. The file can be email and attached but soon after i download the file, the file cant be read. It's seem corrupted. Totally cant be read although i'm using context or wordfile. Original file generated at ek_bkup/alert/tbspace_datafile.log is OK..... ... (7 Replies)
Discussion started by: adzuanamir
7 Replies

5. Shell Programming and Scripting

pls help

Hi, I need your help guys. I have two data files, namely 101.amberized.pdb & 101.pdb . Now I want to replace the whole 3rd column of 101.amberized.pdb with the 3rd column of 101.pdb file. How do I do it in shell? Thanks in advance Parimal (11 Replies)
Discussion started by: chuchu
11 Replies

6. Shell Programming and Scripting

pls help

I have a list of variables: ss1, ss5, ss6, ss8, st2 etc. (these values are not fixed, configurable). Now, I have assigned ss5=”test”. And I want to search in the list for the string “test” to know which variable is having the value “test”. Can u pls tell me how to do this? (10 Replies)
Discussion started by: kanchan_cp
10 Replies

7. UNIX for Dummies Questions & Answers

Help pls!

Hi... Why should I press F1 to start windows?! I have Xp in my computer... thx 4 help Cano (1 Reply)
Discussion started by: Cano
1 Replies

8. UNIX for Dummies Questions & Answers

Pls Help

Hi every one I have got very very bad Email, My question is: How can I get all information about that f*** Email, I do mean IP,reall name, Adress, user name, password etc... I wonder if there is any program or website that I can see that email, help me please When I used windows Xp(old... (2 Replies)
Discussion started by: Cano
2 Replies

9. UNIX for Dummies Questions & Answers

Need help pls

Hi, I'm a newbie. I need help on my first assignment in UNIX. 1. How do I determine the number of non-empty directories? I was told to create a variable ARCHIVE, which points to the directory that contains the archive of the messages. But I'm so dumb and I don't even know how to do this. 2. In... (1 Reply)
Discussion started by: hygsg
1 Replies

10. Linux

pls help me

we hv a big enviroment networked. we use squid proxy. access allowed by src address previously. we have win2000 network with ads. my requirement is the proxy should allow domain users only for access. how can i map my windows userdatabase with squid is there any thing specific which has 2 b... (1 Reply)
Discussion started by: sriram.s
1 Replies
Login or Register to Ask a Question