Solaris 10 Jumpstart Error

Thread Tools Search this Thread
Operating Systems Solaris Solaris 10 Jumpstart Error
# 1  
Old 08-27-2015
Solaris 10 Jumpstart Error

Hey All,

I'm trying to jump start a new Sun Server from an existing jump start server, but this last machine is giving me driver errors :s

It doesn't make sense as we've built a few of these exact same servers just recently, but this last one displays:

"No driver (or driver binding) was found for the interface used to boot.
A driver (or driver binding) may be available in an updated or patch from
Sun, or from the interface vendor."

Has anyone seen this error before? From the research I've done it suggests that I have to unpack the miniboot and add in the missing driver, but we have over a dozen of these X4-2's which have jump started just fine.

Any help is appreciated.
Solaris 10 Jumpstart Error-jumpstart_errorpng
# 2  
Old 08-28-2015
What is the version of the Solaris image and what kind of hardware do you try to install?
# 3  
Old 08-28-2015
I realize this might be a really dumb thing to say but have you checked all the BIOS settings with one of your good machines? Especially the network interface settings in the Advanced section.

Also, perhaps try a Linux (or similar) 'live CD/DVD' to test that the network interface is not hardware faulty.

Apologies if that sounds too obvious.
Login or Register to Ask a Question

Previous Thread | Next Thread

9 More Discussions You Might Find Interesting

1. Solaris

Jumpstart Solaris 10

I have a laptop and need to build an Oracle Linux kickstart server and a Solaris Jumpstart server that can build sparc and x86 systems. Is the best way to create a dual boot from grub for Oracle Linux and Solaris x86? Can the Oracle Kickstart be used as a Jumpstart to build both Solaris 10... (2 Replies)
Discussion started by: Gian
2 Replies

2. Solaris

Issue after jumpstart with Solaris 10 u7

I am performing this installation on a Sun T5220. There is an aftermarket Adaptec StorageTek raid controller card installed. I have created the raid array, and it is referred to as c1t0d0. Here is the profile I have created: install_type initial_install system_type server cluster SUNWCXall... (4 Replies)
Discussion started by: msarro
4 Replies

3. Solaris

Jumpstart Solaris 10

Hello everyone, I tried to install solaris 10 using the command # boot net - install. I take the image correctly but when you start installing the Operating system installation takes a long (4 hours I have left and not advancing but not send me any errors), it can be seen from the following: ... (7 Replies)
Discussion started by: yflores
7 Replies

4. Solaris

Jumpstart Issues Solaris 10

I'm trying to jumpstart my remote server. My /etc/hosts and /etc/ethers files have the correct data. Keep getting the following message at the ok prompt after running a boot net - install Link hasn't comeup yet Ran a test-net and got the following message. Link is -- down When... (7 Replies)
Discussion started by: soupbone38
7 Replies

5. Solaris

Solaris 10 Jumpstart woes

Hi All I have a Solaris 10 jumpstart boot/config server set up on a subnet, and am trying to use it to build a client (the only other machine on the network). Things start out just fine, with the client booting into the Solaris Installation program, but then it just coredumps just as it's... (4 Replies)
Discussion started by: rickedwards44
4 Replies

6. Solaris

Jumpstart Solaris 10 x86

I need a little help figuring out why my custom jumpstart network installation is dumping me to a manual install. I am trying to install Solaris 10 (unattended) over the wire from my jumpstart server to an HP Proliant DL380 server but I'm having difficulties with the unattended part. So, what... (2 Replies)
Discussion started by: alias.256
2 Replies

7. Solaris

Jumpstart solaris

Hi all , I am trying to jumpstart ( webstart) solaris 9 on E2900 ( client) using the DVD of a V440 server ( jumstart server). I did the setup for the V440 as follows : cleaning up preexisting install client "XXXXXXX" removing XXXXXXXfrom bootparams removing /etc/bootparams, since it is... (14 Replies)
Discussion started by: ppass
14 Replies

8. Solaris

jumpstart Solaris 10 on Solaris 9 server

I just built a jumpstart server on a Solaris 9 sun box and have had no problems jumpstarting other sol9 boxes using the custom rules. I've also copied a Solaris 10 image onto that same solaris 9 server and have had problems loading Solaris 10. These boxes will go directly to the manual OS install... (5 Replies)
Discussion started by: salty
5 Replies

9. Solaris

Solaris 10 Jumpstart Problem

Hi, I build a jumpstart server with a running dhcp server. I already managed to install a x86 client via network. But my sparc clients aren't still working. When booting via network I get the following message: Timeout waiting for ARP/RARP packet I ran "snoop" on the server: client2 ->... (1 Reply)
Discussion started by: Jay_Fisi
1 Replies
Login or Register to Ask a Question

Featured Tech Videos