Login or Register to Ask a Question and Join Our Community


Solaris

T5120 2g ram

Login to Discuss or Reply to this Discussion in Our Community

 
Thread Tools Search this Thread
Operating Systems Solaris T5120 2g ram
# 1  
Old 10-09-2013
T5120 2g ram
Anyone run into an issue where a new Solaris 11.1 install on a t5120 will only have access to 2g ram? The system has 16g installed and fmadm isn't reporting any problems. Here's some output that may help.

Oh, and this is a brand new operating system install, there's no zones, ldoms, rcap or the like... Just an out of the box install. This hardware used to have a ldom config on it, but that's been quite a while ago. On a 5120 there's no way for the SP to limit OS access to resources, is there? Or, is there an easy procedure to ensure there's no resource limiting in place?

Code:
dtrapani@atlopscenter:~$ vmstat
 kthr      memory            page            disk          faults      cpu
 r b w   swap  free  re  mf pi po fr de sr s3 s4 s5 sd   in   sy   cs us sy id
 0 0 0 1509776 793296 18 36  0  0  0  0  3 15  0  0  0 1687 6564 2032  2  2 96

Code:
System Configuration:  Oracle Corporation  sun4v SPARC Enterprise T5120
Memory size: 2048 Megabytes

================================ Virtual CPUs ================================


CPU ID Frequency Implementation         Status
------ --------- ---------------------- -------
0      1165 MHz  SUNW,UltraSPARC-T2     on-line  
1      1165 MHz  SUNW,UltraSPARC-T2     on-line  
2      1165 MHz  SUNW,UltraSPARC-T2     on-line  
3      1165 MHz  SUNW,UltraSPARC-T2     on-line  
4      1165 MHz  SUNW,UltraSPARC-T2     on-line  
5      1165 MHz  SUNW,UltraSPARC-T2     on-line  
6      1165 MHz  SUNW,UltraSPARC-T2     on-line  
7      1165 MHz  SUNW,UltraSPARC-T2     on-line  

======================= Physical Memory Configuration ========================
Segment Table:
--------------------------------------------------------------
Base           Segment  Interleave   Bank     Contains
Address        Size     Factor       Size     Modules
--------------------------------------------------------------
0x0            16 GB    4            4 GB     MB/CMP0/BR0/CH0/D0
                                              MB/CMP0/BR0/CH1/D0
                                     4 GB     MB/CMP0/BR1/CH0/D0
                                              MB/CMP0/BR1/CH1/D0
                                     4 GB     MB/CMP0/BR2/CH0/D0
                                              MB/CMP0/BR2/CH1/D0
                                     4 GB     MB/CMP0/BR3/CH0/D0
                                              MB/CMP0/BR3/CH1/D0


================================ IO Devices ================================
Slot +            Bus   Name +                            Model      Speed   
Status            Type  Path                                                 
----------------------------------------------------------------------------
MB/NET0           PCIE  network-pciex8086,105e                       --
                        /pci@0/pci@0/pci@1/pci@0/pci@2/network@0    
MB/NET1           PCIE  network-pciex8086,105e                       --
                        /pci@0/pci@0/pci@1/pci@0/pci@2/network@0,1  
MB/NET2           PCIE  network-pciex8086,105e                       --
                        /pci@0/pci@0/pci@1/pci@0/pci@3/network@0    
MB/NET3           PCIE  network-pciex8086,105e                       --
                        /pci@0/pci@0/pci@1/pci@0/pci@3/network@0,1  
MB/SASHBA         PCIE  scsi-pciex1000,58                 LSI,1068E  --
                        /pci@0/pci@0/pci@2/scsi@0                   
MB/RISER1/PCIE1   PCIE  SUNW,qlc-pciex1077,2432           QLE2460    --
                        /pci@0/pci@0/pci@8/pci@0/pci@1/SUNW,qlc@0   
MB/RISER0/PCIE0   PCIE  SUNW,qlc-pciex1077,2432           QLE2460    --
                        /pci@0/pci@0/pci@8/pci@0/pci@9/SUNW,qlc@0   
MB                PCIX  usb-pciclass,0c0310                          --
                        /pci@0/pci@0/pci@1/pci@0/pci@1/pci@0/usb@0  
MB                PCIX  usb-pciclass,0c0310                          --
                        /pci@0/pci@0/pci@1/pci@0/pci@1/pci@0/usb@0,1
MB                PCIX  usb-pciclass,0c0320                          --
                        /pci@0/pci@0/pci@1/pci@0/pci@1/pci@0/usb@0,2

============================ Environmental Status ============================
Fan sensors:
----------------------------------------------------------------
Location                           Sensor             Status    
----------------------------------------------------------------
SYS/FANBD0/FM0/F0                  TACH               ok
SYS/FANBD0/FM0/F1                  TACH               ok
SYS/FANBD0/FM1/F0                  TACH               ok
SYS/FANBD0/FM1/F1                  TACH               ok
SYS/FANBD0/FM2/F0                  TACH               ok
SYS/FANBD0/FM2/F1                  TACH               ok
SYS/FANBD0/FM3/F0                  TACH               ok
SYS/FANBD0/FM3/F1                  TACH               ok
SYS/FANBD1/FM0/F0                  TACH               ok
SYS/FANBD1/FM0/F1                  TACH               ok
SYS/FANBD1/FM1/F0                  TACH               ok
SYS/FANBD1/FM1/F1                  TACH               ok
SYS/FANBD1/FM2/F0                  TACH               ok
SYS/FANBD1/FM2/F1                  TACH               ok

Fan indicators:
----------------------------------------------------------------
Location                           Sensor             Condition 
----------------------------------------------------------------
SYS/PS0                            FAN_FAULT          ok      
SYS/PS1                            FAN_FAULT          ok      

Temperature sensors:
----------------------------------------------------------------
Location                           Sensor             Status    
----------------------------------------------------------------
SYS/MB                             T_AMB              ok
SYS/MB/CMP0/BR0/CH0/D0             T_AMB              ok
SYS/MB/CMP0/BR0/CH1/D0             T_AMB              ok
SYS/MB/CMP0/BR1/CH0/D0             T_AMB              ok
SYS/MB/CMP0/BR1/CH1/D0             T_AMB              ok
SYS/MB/CMP0/BR2/CH0/D0             T_AMB              ok
SYS/MB/CMP0/BR2/CH1/D0             T_AMB              ok
SYS/MB/CMP0/BR3/CH0/D0             T_AMB              ok
SYS/MB/CMP0/BR3/CH1/D0             T_AMB              ok
SYS/MB/CMP0                        T_TCORE            ok
SYS/MB/CMP0                        T_BCORE            ok

Temperature indicators:
----------------------------------------------------------------
Location                           Indicator          Condition
----------------------------------------------------------------
SYS/PS0                            TEMP_FAULT         ok      
SYS/PS1                            TEMP_FAULT         ok      

Current sensors:
----------------------------------------------------------------
Location                           Sensor             Status    
----------------------------------------------------------------
SYS/PS0                            I_IN_MAIN          ok
SYS/PS0                            I_IN_LIMIT         ok
SYS/PS0                            I_OUT_MAIN         ok
SYS/PS0                            I_OUT_LIMIT        ok
SYS/PS1                            I_IN_MAIN          ok
SYS/PS1                            I_IN_LIMIT         ok
SYS/PS1                            I_OUT_MAIN         ok
SYS/PS1                            I_OUT_LIMIT        ok

Current indicators:
----------------------------------------------------------------
Location                           Indicator          Condition
----------------------------------------------------------------
SYS/MB                             I_USB0             ok      
SYS/MB                             I_USB1             ok      
SYS/PS0                            CUR_FAULT          ok      
SYS/PS1                            CUR_FAULT          ok      

Voltage sensors:
----------------------------------------------------------------
Location                           Sensor             Status    
----------------------------------------------------------------
SYS/MB                             V_VMEML            ok
SYS/MB                             V_VMEMR            ok
SYS/MB                             V_+3V3_STBY        ok
SYS/MB                             V_VCORE            ok
SYS/MB                             V_+3V3_MAIN        ok
SYS/MB                             V_VDDIO            ok
SYS/MB                             V_+12V0_MAIN       ok
SYS/MB                             V_VBAT             ok
SYS/PS0                            V_IN_MAIN          ok
SYS/PS0                            V_OUT_MAIN         ok
SYS/PS1                            V_IN_MAIN          ok
SYS/PS1                            V_OUT_MAIN         ok

Voltage indicators:
----------------------------------------------------------------
Location                           Indicator          Condition
----------------------------------------------------------------
SYS/MB                             VCORE_POK          ok      
SYS/MB                             VMEML_POK          ok      
SYS/MB                             VMEMR_POK          ok      
SYS/PS0                            AC_POK             ok      
SYS/PS0                            DC_POK             ok      
SYS/PS0                            VOLT_FAULT         ok      
SYS/PS1                            AC_POK             ok      
SYS/PS1                            DC_POK             ok      
SYS/PS1                            VOLT_FAULT         ok      

LEDs:
----------------------------------------------------------------
Location                           LED                State   
----------------------------------------------------------------
SYS                                SERVICE            off     
SYS                                LOCATE             off     
SYS                                ACT                steady  
SYS                                PS_FAULT           off     
SYS                                TEMP_FAULT         off     
SYS                                FAN_FAULT          off     
SYS/MB/CMP0/BR0/CH0/D0             SERVICE            off     
SYS/MB/CMP0/BR0/CH1/D0             SERVICE            off     
SYS/MB/CMP0/BR1/CH0/D0             SERVICE            off     
SYS/MB/CMP0/BR1/CH1/D0             SERVICE            off     
SYS/MB/CMP0/BR2/CH0/D0             SERVICE            off     
SYS/MB/CMP0/BR2/CH1/D0             SERVICE            off     
SYS/MB/CMP0/BR3/CH0/D0             SERVICE            off     
SYS/MB/CMP0/BR3/CH1/D0             SERVICE            off     
SYS/HDD0                           SERVICE            off     
SYS/HDD0                           OK2RM              off     
SYS/HDD1                           SERVICE            off     
SYS/HDD1                           OK2RM              off     
SYS/HDD2                           SERVICE            off     
SYS/HDD2                           OK2RM              off     
SYS/HDD3                           SERVICE            off     
SYS/HDD3                           OK2RM              off     
SYS/HDD4                           SERVICE            off     
SYS/HDD4                           OK2RM              off     
SYS/HDD5                           SERVICE            off     
SYS/HDD5                           OK2RM              off     
SYS/HDD6                           SERVICE            off     
SYS/HDD6                           OK2RM              off     
SYS/HDD7                           SERVICE            off     
SYS/HDD7                           OK2RM              off     
SYS/FANBD0/FM0                     SERVICE            off     
SYS/FANBD0/FM1                     SERVICE            off     
SYS/FANBD0/FM2                     SERVICE            off     
SYS/FANBD0/FM3                     SERVICE            off     
SYS/FANBD1/FM0                     SERVICE            off     
SYS/FANBD1/FM1                     SERVICE            off     
SYS/FANBD1/FM2                     SERVICE            off     

============================ FRU Status ============================
Location                           Name      Status  
------------------------------------------------------
SYS                                MB        enabled  
SYS/MB                             RISER0    enabled  
SYS/MB                             RISER1    enabled  
SYS/MB                             RISER2    enabled  
SYS/MB                             SCC_NVRAM enabled  
SYS/MB/CMP0/BR0/CH0                D0        enabled  
SYS/MB/CMP0/BR0/CH1                D0        enabled  
SYS/MB/CMP0/BR1/CH0                D0        enabled  
SYS/MB/CMP0/BR1/CH1                D0        enabled  
SYS/MB/CMP0/BR2/CH0                D0        enabled  
SYS/MB/CMP0/BR2/CH1                D0        enabled  
SYS/MB/CMP0/BR3/CH0                D0        enabled  
SYS/MB/CMP0/BR3/CH1                D0        enabled  
SYS                                HDD0      enabled  
SYS                                HDD1      enabled  
SYS                                HDD2      Not present
SYS                                HDD3      Not present
SYS                                HDD4      Not present
SYS                                HDD5      Not present
SYS                                HDD6      Not present
SYS                                HDD7      Not present
SYS                                PDB       enabled  
SYS                                PADCRD    enabled  
SYS                                SASBP     enabled  
SYS                                DVD       enabled  
SYS                                USBBD     enabled  
SYS                                FANBD0    enabled  
SYS/FANBD0                         FM0       enabled  
SYS/FANBD0                         FM1       enabled  
SYS/FANBD0                         FM2       enabled  
SYS/FANBD0                         FM3       enabled  
SYS                                FANBD1    enabled  
SYS/FANBD1                         FM0       enabled  
SYS/FANBD1                         FM1       enabled  
SYS/FANBD1                         FM2       enabled  
SYS                                PS0       enabled  
SYS                                PS1       enabled  

============================ FW Version ============================
Version
------------------------------------------------------------
 Sun System Firmware 7.4.5 2012/12/11 23:47


====================== System PROM revisions =======================
Version
------------------------------------------------------------
OBP 4.33.6.b 2012/12/11 20:50

Chassis Serial Number
---------------------
XXXXXXXXXXXXXXXX

# 2  
Old 10-09-2013
Maybe you have LDOMs configured? Edit: I just read that the system had LDOMs configured. What does this say:
Code:
ldm ls-config
ldm ls

# 3  
Old 10-09-2013
Nah, it's a clean install man... wiped the drives and everything.

Code:
ldm: not found

# 4  
Old 10-09-2013
Install the ldm tools and check the asked command.
# 5  
Old 10-10-2013
Quote:
Originally Posted by DukeNuke2
Install the ldm tools and check the asked command.
D'oh! Thanks....
Code:
ldm ls
NAME             STATE      FLAGS   CONS    VCPU  MEMORY   UTIL  UPTIME
primary          active     -n-cv-  SP      8     2G       0.2%  6m

Code:
ldm list
NAME             STATE      FLAGS   CONS    VCPU  MEMORY   UTIL  UPTIME
primary          active     -n-cv-  SP      8     2G        22%  5m
dtrapani@atlopscenter:~$ ldm ls-config
factory-default
ldom_jet
xvmconfig [next poweron]

So, I really just need a simple, bare metal OS install. No ldoms needed.

---------- Post updated at 08:19 AM ---------- Previous update was at 08:12 AM ----------

Just a quick note, I successfully ran the following command
Code:
ldm add-memory 15g primary

ldm list output now shows 15g ram available to the primary. I'd still like to revert to a simple install. Did I use the wrong installation media?
# 6  
Old 10-10-2013
You don't need to revert anything.

Just allocate everything to domain primary (i recommend start-reconf, add all mem and cpu to primary and reboot).

Then use your operating system as you see fit.
# 7  
Old 10-10-2013
Quote:
Originally Posted by Peasant
You don't need to revert anything.

Just allocate everything to domain primary (i recommend start-reconf, add all mem and cpu to primary and reboot).

Then use your operating system as you see fit.
Ok, thanks.

It's obvious to me this system was previously configured as a ldom server. If I want to wipe out 100% of the previous config and start from scratch, what do I need to do?

---------- Post updated at 10:56 AM ---------- Previous update was at 09:37 AM ----------

I answered my own question.


http://docs.oracle.com/cd/E19227-01/...oms/index.html
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. Solaris

SP T5120

I have 2machines, 1 T5120 and 1 T5240. Just wandering everytime we have powershutdown, I need to connect thru SP console to boot the T5120. The other machine T5240 is ok and can boot normally after I press the power button. On T5120, no matter how I press the power button, it just stays there,... (3 Replies)
Discussion started by: lhareigh890
3 Replies

2. Solaris

ILOM question on T5120 server

I have a T5120 server and we found out on a security scan that the web interface for the ILOM is enabled. I have been trying to find this information in the wonderful documentation but have not been successful. Does anyone know if you need the http/https enabled on the ILOM for the serial... (4 Replies)
Discussion started by: rkruck
4 Replies

3. Solaris

Sun T5120 hardware RAID question

Hi everyone I've just purchased a Sun T5120 server with 2 internal disks. I've configured hardware RAID (mirror) and as a result the device tree in Solaris only contains 1 hard drive. My question is, how would I know when one of the drives become faulty? Thanks (2 Replies)
Discussion started by: soliberus
2 Replies

4. Solaris

conecting to t5120 with hyperterminal....

greetings. im a very new user to solaris (and to servers for that matter) and i need to conect to a t5120 sun server, i tried using the SER-MGT port on the back of the server, then to a rj-45/db-9 adaptor, and to a serial-usb adaptor (my laptop doesn't have a com port). when i try to conect with... (2 Replies)
Discussion started by: darklilith
2 Replies

5. Solaris

change root password on t5120

hi all, i have a problem with a sun server, since a while the root password has been lost and now that we need to give maintenance to the services hosted in it, we cant access it, i tried a method to change it by booting from cd but i cant direct the server to boot from the cd. (The server is on... (3 Replies)
Discussion started by: darklilith
3 Replies

6. Solaris

Small issue with Sun Sparc Enterprise T5120

Good Day, We have bought Sun Sparc Enterprise T5120 with pre-installed Solaris 10 Sparc But i need on this server Solaris 9. I have inserted in to DVD-rom (USB DVD-rom) with Solaris 9 for Sparc. Then log into shell and type: reboot -- cdrom. System rebooted and i have this message: ... (3 Replies)
Discussion started by: A.Shalin
3 Replies

7. Solaris

How to destroy hardware raid on T5120

Hi, I have problem creating hardware raid on T5120 with 4 disks. After the hardware raid 1 created, then I used the raidctl -l c1t0d0 and raidctl -l c1t2d0 the output of volume c1t0d0 contain disk 0.0.0 0.1.0, also the volume c1t2d0 contain disk 0.0.0 0.1.0 and should be 0.2.0 0.3.0 so I... (15 Replies)
Discussion started by: netlink
15 Replies

8. Solaris

firmware update on t5120

Hi, I am using 3 t5120 sparc systems, OS solaris 10. I am confused by update manager behaviour and sun support. Sun support guy, tells me install patch : 136932-09 (#136932-09: Hardware/PROM: SPARC Enterprise T5120 & T5220 Sun System Firmware with LDOMS support) When I checked... (4 Replies)
Discussion started by: upengan78
4 Replies

9. Red Hat

red hat Linux 5.0 is detecting 3gb ram but physical ram is 16gb

Hi, On server 64bit Hw Arch , Linux 5.0(32bit) is installed it is showing only 3gb of ram though physical is 16gb can u give me idea why? (4 Replies)
Discussion started by: manoj.solaris
4 Replies

10. Solaris

how to hardware RAID 1 on T5120

Hi, I have t5120 sparc and I have 2 146 G drives in the system. I will be installing solaris 10 and also want the system mirrored using Hardware RAID "1" The System did come preinstalled as it comes from sun. I did not do much on it. I booted system using boot cdrom -s gave format... (6 Replies)
Discussion started by: upengan78
6 Replies
Login or Register to Ask a Question