ifconfig ge0 plumb


 
Thread Tools Search this Thread
Operating Systems Solaris ifconfig ge0 plumb
# 15  
Old 06-16-2012
I did that but I didn't got any prompt to reconfigure my server, I event tried to get init 0 and the boot -r and that didnt worked.

After the boot the ge0 is not getting up.
# 16  
Old 06-17-2012
I'd say that the driver is not seeing the card because the driver is either wrong or corrupt. Revert to card manufacturers instructions on installing the driver on this system.

Let's see what other suggestions are forthcoming from forum members.
# 17  
Old 06-18-2012
Is the "ge" module even loaded? What's the output from modinfo?

And again - try to boot with the "-v" option. From a login shell, that ould be done by:

Code:
reboot -- -r -v

# 18  
Old 06-19-2012
Achenle,

Doesn´t looks like the module was loaded.

Code:
# modinfo | grep eri
105 7bf7c000   9340  29   1  zs (Z8530 serial driver V4.131)
109 7bf8a000   3ff8   -   1  usbser (USB generic serial module 1.18)
133 7bfee000   f6d8   8   1  eri (10/100 Mb Ethernet Driver v1.40)
155 7b73f340    ae8  31   1  seeprom (I2C serial EEPROM device driver)

# modinfo | grep ge
  1  10a3590 21d370   -   0  genunix ()
 13  12907d0  91ed8 256   1  zfs (ZFS storage pool)
 16  132ff48   5260   -   1  sha1 (SHA1 Message-Digest Algorithm)
 55 7bb34000   2b58   -   1  md5 (MD5 Message-Digest Algorithm)
109 7bf8a000   3ff8   -   1  usbser (USB generic serial module 1.18)
123 7be18e70   1718  97   1  sysmsg (System message redirection (fan)
144 7be94000  2f198  85   1  md (Solaris Volume Manager base mod)
151 7b6c9148   4d98 130   1  fcsm (Sun FC SAN Management v20090728)
181 7b71dcc8    cb8 272   1  fm (fault management driver)

reboot -- -r -v

Code:
Rebooting with command: boot -r -v
Boot device: /pci@8,600000/SUNW,qlc@2/fp@0,0/disk@w21000004cf96ed25,0:a  File and args: -r -v
module /platform/sun4u/kernel/sparcv9/unix: text at [0x1000000, 0x10a358d] data at 0x1800000
module /platform/sun4u/kernel/sparcv9/genunix: text at [0x10a3590, 0x126b757] data at 0x1866800
module /platform/SUNW,Sun-Fire-880/kernel/misc/sparcv9/platmod: text at [0x126b758, 0x126c1cf] data at 0x18bc080
module /platform/sun4u/kernel/cpu/sparcv9/SUNW,UltraSPARC-III+: text at [0x126c200, 0x127f067] data at 0x18bca80
SunOS Release 5.10 Version Generic_141444-09 64-bit
Copyright 1983-2009 Sun Microsystems, Inc.  All rights reserved.
Use is subject to license terms.
Ethernet address = 0:3:ba:b:30:3
mem = 33554432K (0x800000000)
avail mem = 33592369152
root nexus = Sun Fire 880
pseudo0 at root
pseudo0 is /pseudo
scsi_vhci0 at root
scsi_vhci0 is /scsi_vhci
pcisch1 at root: SAFARI 0x8 0x600000
pcisch1 is /pci@8,600000
PCI-device: SUNW,qlc@2, qlc0
qlc0 is /pci@8,600000/SUNW,qlc@2
fp1 is /pci@8,600000/SUNW,qlc@2/fp@0,0
ssd1 at fp1: name w21000004cf96e2f7,0, bus address e8
ssd1 is /pci@8,600000/SUNW,qlc@2/fp@0,0/ssd@w21000004cf96e2f7,0
/pci@8,600000/SUNW,qlc@2/fp@0,0/ssd@w21000004cf96e2f7,0 (ssd1) online
ssd0 at fp1: name w500000e01a6809c1,0, bus address e1
ssd0 is /pci@8,600000/SUNW,qlc@2/fp@0,0/ssd@w500000e01a6809c1,0
/pci@8,600000/SUNW,qlc@2/fp@0,0/ssd@w500000e01a6809c1,0 (ssd0) online
ssd2 at fp1: name w21000004cf96e769,0, bus address ef
ssd2 is /pci@8,600000/SUNW,qlc@2/fp@0,0/ssd@w21000004cf96e769,0
/pci@8,600000/SUNW,qlc@2/fp@0,0/ssd@w21000004cf96e769,0 (ssd2) online
ssd3 at fp1: name w21000004cf96f0a2,0, bus address e2
ssd3 is /pci@8,600000/SUNW,qlc@2/fp@0,0/ssd@w21000004cf96f0a2,0
/pci@8,600000/SUNW,qlc@2/fp@0,0/ssd@w21000004cf96f0a2,0 (ssd3) online
ssd4 at fp1: name w21000011c6412680,0, bus address e0
ssd4 is /pci@8,600000/SUNW,qlc@2/fp@0,0/ssd@w21000011c6412680,0
/pci@8,600000/SUNW,qlc@2/fp@0,0/ssd@w21000011c6412680,0 (ssd4) online
ssd5 at fp1: name w21000004cf96ed25,0, bus address e4
ssd5 is /pci@8,600000/SUNW,qlc@2/fp@0,0/ssd@w21000004cf96ed25,0
/pci@8,600000/SUNW,qlc@2/fp@0,0/ssd@w21000004cf96ed25,0 (ssd5) online
root on rpool/ROOT/s10s_u8wos_08a fstype zfs
pcisch2 at root: SAFARI 0x9 0x700000
pcisch2 is /pci@9,700000
PCI-device: ebus@1, ebus0
ebus0 is /pci@9,700000/ebus@1
todds12870 at ebus0: offset 1,300070
todds12870 is /pci@9,700000/ebus@1/rtc@1,300070
mc-us30 at root: SAFARI 0x0 0x400000 ...
mc-us30 is /memory-controller@0,400000
mc-us31 at root: SAFARI 0x1 0x400000 ...
mc-us31 is /memory-controller@1,400000
mc-us32 at root: SAFARI 0x2 0x400000 ...
mc-us32 is /memory-controller@2,400000
mc-us33 at root: SAFARI 0x3 0x400000 ...
mc-us33 is /memory-controller@3,400000
mc-us34 at root: SAFARI 0x4 0x400000 ...
mc-us34 is /memory-controller@4,400000
mc-us35 at root: SAFARI 0x5 0x400000 ...
mc-us35 is /memory-controller@5,400000
mc-us36 at root: SAFARI 0x6 0x400000 ...
mc-us36 is /memory-controller@6,400000
mc-us37 at root: SAFARI 0x7 0x400000 ...
mc-us37 is /memory-controller@7,400000
pcisch0 at root: SAFARI 0x8 0x700000
pcisch0 is /pci@8,700000
pcisch3 at root: SAFARI 0x9 0x600000
pcisch3 is /pci@9,600000
pseudo-device: dld0
dld0 is /pseudo/dld@0
se0 at ebus0: offset 1,400000
se0 is /pci@9,700000/ebus@1/serial@1,400000
PCI-device: usb@1,3, ohci0
ohci0 is /pci@9,700000/usb@1,3
cpu7: UltraSPARC-III+ (portid 7 impl 0x15 ver 0x23 clock 900 MHz)
cpu0: UltraSPARC-III+ (portid 0 impl 0x15 ver 0x23 clock 900 MHz)
cpu1: UltraSPARC-III+ (portid 1 impl 0x15 ver 0x23 clock 900 MHz)
cpu2: UltraSPARC-III+ (portid 2 impl 0x15 ver 0x23 clock 900 MHz)
cpu3: UltraSPARC-III+ (portid 3 impl 0x15 ver 0x23 clock 900 MHz)
iscsi0 at root
iscsi0 is /iscsi
cpu4: UltraSPARC-III+ (portid 4 impl 0x15 ver 0x23 clock 900 MHz)
cpu5: UltraSPARC-III+ (portid 5 impl 0x15 ver 0x23 clock 900 MHz)
cpu6: UltraSPARC-III+ (portid 6 impl 0x15 ver 0x23 clock 900 MHz)
pseudo-device: zfs0
zfs0 is /pseudo/zfs@0
SUNW,eri0 : Local Ethernet address = 0:3:ba:b:30:3PCI-device: network@1,1, eri0
eri0 is /pci@9,700000/network@1,1
Failed to plumb IPv4 interface(s): ge0
Failed to plumb IPv6 interface(s): ge0
pseudo-device: devinfo0
devinfo0 is /pseudo/devinfo@0
pseudo-device: pseudo1
pseudo1 is /pseudo/zconsnex@1
/pci@8,700000/scsi@1 (glm0):
        Rev. 4 Symbios 53c875 found.
PCI-device: scsi@1, glm0
glm0 is /pci@8,700000/scsi@1
ses16 at fp1: name w50800200001a0bc9,0, bus address dc
ses16 is /pci@8,600000/SUNW,qlc@2/fp@0,0/ses@w50800200001a0bc9,0
/pci@8,600000/SUNW,qlc@2/fp@0,0/ses@w50800200001a0bc9,0 (ses16) online
pseudo-device: fcode0
fcode0 is /pseudo/fcode@0
pseudo-device: llc10
llc10 is /pseudo/llc1@0
gpio_873170 at ebus0: offset 1,300600
gpio_873170 is /pci@9,700000/ebus@1/gpio@1,300600
pseudo-device: fcsm0
fcsm0 is /pseudo/fcsm@0
pseudo-device: lofi0
lofi0 is /pseudo/lofi@0
pseudo-device: trapstat0
trapstat0 is /pseudo/trapstat@0
pseudo-device: mem_cache0
mem_cache0 is /pseudo/mem_cache@0
pseudo-device: fssnap0
fssnap0 is /pseudo/fssnap@0
SUNW,eri0 : 100 Mbps full duplex link up
dump on /dev/zvol/dsk/rpool/dump size 1536 MB
Configuring devices.
pseudo-device: ramdisk1024
ramdisk1024 is /pseudo/ramdisk@1024
pseudo-device: fcp0
fcp0 is /pseudo/fcp@0
su0 at ebus0: offset 1,3062f8
su0 is /pci@9,700000/ebus@1/rsc-control@1,3062f8
su1 at ebus0: offset 1,3083f8
su1 is /pci@9,700000/ebus@1/rsc-console@1,3083f8
sd6 at glm0: target 6 lun 0
sd6 is /pci@8,700000/scsi@1/sd@6,0

# 19  
Old 06-22-2012
ok . that is 880 server .. assume eri0 is your interface and connect to lan cablr to interface .. otherwise you try
ifconfig eri0 plumb or
ifconfig ce0 or ce1 plumb
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. Solaris

ifconfig hme0 plumb not working

Hiii folks,, I am unable to configure NIC using hme0 command. I am getting an error message as "hme0: File or directory not found.." can someone help me... Bhagi... (9 Replies)
Discussion started by: bhargav90
9 Replies

2. Solaris

Ifconfig command ?

What would be the command to remove the IP address from an interface? I want to remove the ip from this interface: ce3: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 5 inet 155.216.13.74 netmask fffffff0 broadcast 155.216.13.79 ether 0:3:ba:da:a6:96 (3 Replies)
Discussion started by: Kjons76
3 Replies

3. Shell Programming and Scripting

not able to run ifconfig

Unable to run the ifconfig in my home dir.. I did add adding /sbin and /usr/sbin in th PATH But still unable to get that .. Am using red hat linux cat /etc/redhat-release Red Hat Enterprise Linux Server release 5.3 (Tikanga) (3 Replies)
Discussion started by: mail2sant
3 Replies

4. Linux

ifconfig - information

Hi All, I need some info on ifconfig. ifconfig is available in Linux and Solaris. However the options available in Solaris is not there in Linux. 1. ifconfig -a == output is different in both OS. I am somewhat able to compare the output. But one thing I am not getting is after the flags... (2 Replies)
Discussion started by: ahamed101
2 Replies

5. Solaris

cannot plumb nxge on T5240

its a fresh installation. during the OS setup, it did not prompt for IP, netmask and gateway. using Solaris 10 08/07 update 4. I tried to plumb manually but encountered no such interface error. but nxge interfaces can be greped from the /etc/path_to_inst file. getting similar error on... (3 Replies)
Discussion started by: incredible
3 Replies

6. IP Networking

/etc/hosts changes when ifconfig......

Hello everyone. Im using last redhat enterprise edition and in my working environment, i'm always reconfiguring both interfaces , eth0 and eth1, everytime i change any interface, (i use ifconfig to change ip, and after i execute "/etc/init.d/network restart") my "/etc/hosts" file... (9 Replies)
Discussion started by: trutoman
9 Replies

7. Shell Programming and Scripting

ifconfig!!!!

why the ifconfig command is not working in my machine? it says "-bash: ifconfig: command not found" why its says that? actually i m looking for "how can I know the Network Interface Card physical address?" Requesting u all for help. thanks (3 Replies)
Discussion started by: moco
3 Replies

8. Solaris

Before plumb the network interface.....

I know that I could use the #ifconfig hme0 plumb to activate the network interface. However, how can I know the name of the interface e.g. hme0 before I could use the ifconfig to plumb it up? I know there is a command (but I forgot it) to use in the Sparc version when you are in the... (7 Replies)
Discussion started by: heero
7 Replies

9. OS X (Apple)

ifconfig

Hi, I type (as root) "ifconfig en1 ether aa:aa: " but it doesnt change the mac of my airport. Can anyone help me? Thx. (0 Replies)
Discussion started by: Jariya
0 Replies

10. UNIX for Dummies Questions & Answers

ifconfig

I am trying to change an IP address on a machine running HPUX10 After I change it I can ping it from the outside but it completely locks the console. After a reboot it returns back to its previous IP. Any ideas?? Thanks Brian (7 Replies)
Discussion started by: breigner
7 Replies
Login or Register to Ask a Question