Visit Our UNIX and Linux User Community


Solaris Problem


 
Thread Tools Search this Thread
Operating Systems Solaris Solaris Problem
# 1  
Old 05-21-2012
Question Solaris Problem

I have a SUnfire V120 solaris 10 machine I have recently added memory to. After installation of the RAM, powering back on, the machine did not come back on the network. Consoled into the machine, the routing table has been wiped out completely and I had to reconfigure the IP address. I got the IP address reconfigured, but I cannot add a default gateway. I keep getting network unreachable. I am unable to add routes back into the routing table.

I have changed the network cable. I have even tried on the eri1 interface (it's main configuration was on the eri0). I still got the same result.

So, I am thinking perhaps the hardware for the ethernet ports have failed on the shutdown/reboot. Is there something else I can try to get my server back online? or should I find a new server or a Solaris specific tech that can possibly troubleshoot and replace the parts that are broken?

The memory is reading find. I don't think the RAM has affected it. I just think the server is old and hardware failure. I would like to exhaust all my options before officially declaring it "dead". Smilie
# 2  
Old 05-21-2012
Can you post output of ifconfig -aafter you have configured the IP addresses for interfaces?
# 3  
Old 05-21-2012
Code:
# ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
        inet 127.0.0.1 netmask ff000000
eri0: flags=1000851<UP,POINTOPOINT,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
        inet 192.168.209.83 --> 192.168.209.83 netmask ffffff00
        ether 0:3:ba:2d:54:6a

---------- Post updated at 11:01 AM ---------- Previous update was at 10:48 AM ----------

This is what happens when i restart the network interface

Code:
# init.d/network restart
configuring IPv4 interfaces: eri0.
Hostname: unknown
#

 
hostname file is valid and working
 
# more hostname.eri0
192.168.209.83  lvccirt03
#

So i'm not sure why it's saying hostname unknown either. Definitely a strange new problem for me. Typcially resetting the network has fixed in the past. But nothing seems to be working.

Last edited by Scrutinizer; 05-21-2012 at 04:54 PM.. Reason: code tags
# 4  
Old 05-21-2012
After you assign 192.168.209.83 as IP address, can you ping gateway?
# 5  
Old 05-21-2012
From the out's it is showing as POINTOPOINT, so you can't expect it to be broadcasting on the network. I was in similar situation(where network was not detected, after I added additional eth's interface on a VM image)

So first check through /var/log/messages about any info on this scenario

Or simply go for reconfiguring the eri0 mate.

check through dladm show-dev for available interface..

Last edited by solaris040; 05-21-2012 at 05:20 PM.. Reason: solaris
# 6  
Old 05-21-2012
This is b/c you are configuring the eri0 as pointopoint, check the flags:

Code:
<UP,POINTOPOINT,RUNNING,MULTICAST,IPv4>

Take a look at the configuration files,

If you want to do the configuration manually you can still do:

Code:
ifconfig eri0 unplumb
ifconfig eri0 plumb
ifconfig er0 <IP> netmask <MASK>
route add default <GW>

and it should work.

Cheers

Juan


Last edited by Scott; 05-21-2012 at 06:40 PM.. Reason: Code tags
# 7  
Old 05-21-2012
I cannot ping the gateway. if I try to add the gateway:
Code:
# route add default 192.168.209.1
add net default: gateway 192.168.209.1: Network is unreachable
# ping 192.168.209.1
ICMP Host Unreachable from gateway lvccirt03 (192.168.209.83)
for icmp from lvccirt03 (192.168.209.83) to 192.168.209.1
ICMP Host Unreachable from gateway lvccirt03 (192.168.209.83)
for icmp from lvccirt03 (192.168.209.83) to 192.168.209.1
ICMP Host Unreachable from gateway lvccirt03 (192.168.209.83)

and for some screwed up reason, dladm is not installed on this system. I cannot use that. AND there is no /var/log/messages which i find very unusual. i'm fairly certain that pathway was there previously and on the servers it is identical to. There is definitely something unusual going on with this machine.

Last edited by Scott; 05-21-2012 at 06:40 PM.. Reason: Code tags

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. Solaris

Problem boot Solaris

Hi I have a problem on a server, when he boot I have this type of message loop, do you know what it corresponds to ? ( requesting internet Adress for 0:3:ba:fa:33:91 ) Regards Sun Fire V240, No Keyboard Copyright 2007 Sun Microsystems, INC. All rights reserved. openboot 4.22.33,... (10 Replies)
Discussion started by: yoyo-tns
10 Replies

2. Solaris

Solaris 10 problem - need help

I installed Solaris 10 on UltraSparc T5120. The machine shows yellow triagle ! LED. I got endless Warnings on console connection WARNING: /pci@0/pci@0/pci@1/pci@0/pci@1/pci@0/usb@0,2/hub@4/device@4/storage@0/disk@0,0 (sd6): Error for Command: read(10) Error Level: Fatal... (9 Replies)
Discussion started by: gping
9 Replies

3. Solaris

T3-2 and Solaris 10 Problem

Hi Guys, I got a unique (and wierd) problem with trying to install Solaris 10 off of a DVD on a T3-2. You boot cdrom, it goes through the questions and then when it comes to ask you if you want to install using nfs or dvd if you pick dvd it comes up with an error - ERROR: The disc you inserted... (8 Replies)
Discussion started by: callmebob
8 Replies

4. Solaris

Problem with Solaris 11.1 vm

Hi! I have the following problem: I tried to create a Solaris 11.1 virtual machine in the latest VMware Workstation (10.0.1) and despite my efforts it is impossible to make the Tools running. During the installation I receive the following messages: root@solaris:... (0 Replies)
Discussion started by: apollookc
0 Replies

5. Solaris

Solaris 8 -> Solaris 10 = problem :/

Hello, I have a multithreading program (just two threads) which works on Solaris 8. I use pthread library to synchronize threads. I try to run it on Solaris 10 (on another computer). All sources was re-compiled but behaviour of my program is not the same. The thread 2 is never executed when... (3 Replies)
Discussion started by: Tinkh
3 Replies

6. Shell Programming and Scripting

sed Solaris Problem

Hello. has anybody an idea why my script doesnt work on solaris but on ubuntu? I know. I ask the same question again. But i really dont know why my script is not working. #!/usr/xpg4/bin/sh for file in $(find /home9/user/..../.../Test/ -type f) do head -n 1 $file | egrep '^#!' if ... (2 Replies)
Discussion started by: fertchen
2 Replies

7. Solaris

Solaris 10 LU problem

I have a problem with export/home after doing the upgrade. The df -k shows /export and /export/home both being mounted on the same slice. Yes, both are in the vfstab file too. When I reformatted the disk for the upgrade, I added 10gb to the /export partition so that is the one I want to end up... (3 Replies)
Discussion started by: zeekstern
3 Replies

8. Solaris

Solaris 10 - X Problem

I can't get a remote X session to display on my Solaris 10 box. I can get it to work if I launch X on my local machine (like /usr/openwin/bin/xclock) so I know X itself is working correctly. The problem is, when I am on a remote host, I set the variable, and run /usr/openwin/bin/xclock, and it... (5 Replies)
Discussion started by: pc9456
5 Replies

9. UNIX for Dummies Questions & Answers

Problem with Solaris 9

I'm trying to install this on my pc at home but the thing is after I get to the option screen that ask where I want to boot solaris from: hard drive cd interface after I choose the cd option, it begins reading from the CD then it asks me if I want the installation to be interactive or... (3 Replies)
Discussion started by: TRUEST
3 Replies

10. UNIX for Dummies Questions & Answers

problem in solaris 8

hi, I have install solaris 8 7/01 in ULTRA 10,but when I type commands such like "admintool" and "swtool",there will be a error messege: warning:Missing charsets in string to fontset conversion arithmetic exception - core dumped I dont know what these mean,can anyone help me?thank... (1 Reply)
Discussion started by: fuqiang1976
1 Replies

Featured Tech Videos