Hi everybody,
I'm having big troubles in installing Solaris 8 on a Sun Blade 150.
Here are some system specs:
When I try to boot from Solaris 8 CD with boot cdrom or boot cdrom -s I receive the following messages:
This process creates a boot loop. I have to stop+A to end it.
I've also managed to install Solaris 8, from same CDs, on another Sun Blade 150, with similar hardware and software (the Openboot is a bit holder on this one: OBP 4.6.5). After a successful installation I moved the HDD to the other Sun Blade, the one who gives me problems. The result is the same: I get the same error that I receive when I try to boot from CD.
looks like a hardware error... so there won't be much that you can do... what i would try is a POST with MAX settings to see if the system can detect any errors during powerup. you'll need a seriell connection to the system to check the output of the POST.
I'm not sure if it is a Hardware issue... you try to install a very old Solaris version... Try to start the installation using a SOlaris 10 DVD, if it works it could be the driver solaris 8 is using or even a bug on the Solaris 8 installation process.
Try to find the latest solaris 8 Installation CDs, that might fix it as well..
solaris 10 will not work with 256mb ram... i think 384 (or 348)mb ram is minimum for solaris 10. the newest solaris 8 release should work fine with a blade 150 (which is a rather old system, too).
GA date for the blade 150 was august 2002. a minimum release of solaris 8 2/02 is needed! so yes, maybe your used solaris 8 version is to old for the blade...
hello
i have a forte gamma camera Philips device . and its a medical device. this medical device is came with sun blade 150 pc and pegasys is printed on the sun blade pc .the problem is when i switched the power on , the sun blade runs and a white screen appear with the information about the... (6 Replies)
Hello,
I cant get my blade box to boot off the harddrive after installing solaris 10.I can get to a root prompt after issuing "boot cdrom -s".I tried booting off disk0 and disk1,but I get "the file just loaded does not seem to be executable".Thanks for any help.:wall: (4 Replies)
Hello,
Ive just aquired a blade 150 off ebay.Im new to suns and are having a problem getting it to boot off the cdrom.Openboot continuously tries to do a network boot and I cant enter any commands.Im using an average pc keyboard and it definetly works.Thanks for any help.:wall: (3 Replies)
I have recently re-installed Solaris 10 on a Sun Blade 150 followed by a patch set (10_Recommended) dated 2011.12.05.
I have just noticed /bin/sun now returns false, rather than true. See below.
$ uname -a
SunOS myblade1 5.10 Generic_147440-07 sun4u sparc SUNW,Sun-Blade-100
$ /bin/sparc &&... (1 Reply)
Hi,
I have a Solaris 8.0 BLADE 150 machine. I have an onboard graphics alongwith an addon XVR500 graphics card. Now, when I use the motherboard graphics, I am not able to login to the XWINDOWS terminal, instead it stays on the console.
But, if I insert the monitor cable to the XVR500 port,... (2 Replies)
We had to replace a hard drive in one of our Sun Blade 150s, but now it hangs during the Jumpstart. It will show 1 or 2 Timeout for ARP/RARP messages and then start the spinning numbers. It always stops at 2ae00 and just hangs there.
We have 1 combined jumpstart server and it is also our NIS+... (5 Replies)
I'm not familiar with this particular machine and it's baffling me. For those that are familar with the workstation, allow me to paint a picture. If you were looking down on the machine (open) you would see the main board and then a riser board. On the left side of the riser board are jacks... (1 Reply)
Hi, I am new to UNIX. I have a Sun Blade 150 worksation. I used a Dell monitor and Dell keyboard as input and output devices. However, workstation always told me that keyboard couldn't be found. I used Dell keyboard with USB and Dell keyboard with series connector. It all didn't work. Please help... (10 Replies)
I would like to upgrade the memory in my Sun Blade 150 workstation. In reading through Sun's Blade 150 DIMM Installation Guide, it indicates that the memory must be "certified by Sun for the Sun Blade 150 system."
Does anyone know if any SDRAM, PC133 • CL=2 • Unbuffered • ECC • 133MHz • 3.3V ... (2 Replies)