10 More Discussions You Might Find Interesting
1. BSD
Hello,
MBR partition table made by linux fdisk looks certainly not correct when printed by openbsd fdisk:
Partition table created on linux (centos 6.3):
# fdisk -l /dev/sdc
Disk /dev/sdc: 10.7 GB, 10737418240 bytes
255 heads, 63 sectors/track, 1305 cylinders
Units = cylinders of 16065 *... (2 Replies)
Discussion started by: vilius
2 Replies
2. Red Hat
Hello,
I have been going through our environment and I see we have a few servers with LVM's setup and the file system type is still set to "83" within fdisk. If I change this to "8e", will it hurt the data or cause any loss? I need to know for sure before I make the change. (1 Reply)
Discussion started by: s ladd
1 Replies
3. Shell Programming and Scripting
Hi,
How can I run fdisk partition in a script without interactive input?
In manual procedure, I run fdisk device, select n, select p, presess enter for default start number (1), press enter to default end number, then select w for writing to the partition table. The command looks like... (3 Replies)
Discussion started by: hce
3 Replies
4. Solaris
I'm preparing to recover a Oracle Fire X4170 server in a disaster recovery test at a different location than in prod. I have some questions about fdisk partitions. I'm using Solaris 10 update 10.
On my prod server, the boot disk has 2 partitions, diagnostic and solaris. Is the diagnostic... (1 Reply)
Discussion started by: TKD
1 Replies
5. Filesystems, Disks and Memory
Hi!
I have a really big problem right now. I (accidently) formatted a ext3 partition with "mkfs.ext3 /dev/sda1". The problem is that I REALLY need some files from there. The partition had a size of about 4GB, after accidently formatting it, I accidently rewrote Grub on it :wall: I hope I didn't... (3 Replies)
Discussion started by: al0x
3 Replies
6. SCO
hi
How can I backup MBR an Partition Table of SCO 5.0.6? (7 Replies)
Discussion started by: ccc
7 Replies
7. Filesystems, Disks and Memory
Hello,
I have a RHEL system with two 500GB hard drives in RAID 1 (I think hardware, but not 100% certain - any way to tell?).
It looks like it was just set up in default configuration with a small boot partition and one huge partition for the rest, which composes a LVM volume.
I want... (1 Reply)
Discussion started by: builder88
1 Replies
8. UNIX for Advanced & Expert Users
Hello everyone -
Please forgive me if I violate the forum's etiquette as this is my very first post. I'm posting this on both the dummies and the advance section with the hope for any responses.
I stumbled on this forum while frantically looking for an answer to a dumb, ignorant thing I did... (5 Replies)
Discussion started by: kevindoman
5 Replies
9. UNIX for Dummies Questions & Answers
Hello everyone -
Please forgive me if I violate the forum's etiquette as this is my very first post. I'm posting this on both the dummies and the advance section with the hope for any responses.
I stumbled on this forum while frantically looking for an answer to a dumb, ignorant thing I did... (2 Replies)
Discussion started by: kevindoman
2 Replies
10. UNIX for Advanced & Expert Users
Host 1
-------
Part Tag Flag Cylinders Size Blocks
0 root wm 0 - 1911 18.56GB (1912/0/0) 38913024
1 swap wu 1912 - 5434 34.19GB (3523/0/0) 71700096
2 backup wm 0 - 14086 136.71GB ... (5 Replies)
Discussion started by: sriny
5 Replies