Solaris ssh client hangs when connecting to another Solaris machine
Got a strange problem.
I have 4 Solaris servers all configured the same, Solaris 10 x86 update 10.
When I try to ssh from one Solaris 10 server to another server ssh hangs.
I have an identical server and when I try this everything works fine.
The weird thing is if I am root on the server that isn't working when I ssh to another maching it doesn't hang.
Here is the debug output from ssh:
Code:
Sun_SSH_1.1.2, SSH protocols 1.5/2.0, OpenSSL 0x0090704f
debug1: Reading configuration data /etc/ssh/ssh_config
debug1: Rhosts Authentication disabled, originating port will not be trusted.
debug1: ssh_connect: needpriv 0
debug1: Connecting to ggsghpc1 [192.168.2.21] port 22.
debug1: Connection established.
debug1: identity file /home/cjohnson/.ssh/identity type 0
debug3: Not a RSA1 key file /home/cjohnson/.ssh/id_rsa.
debug2: key_type_from_name: unknown key type '-----BEGIN'
debug3: key_read: no key found
debug3: key_read: no space
debug3: key_read: no space
debug3: key_read: no space
debug3: key_read: no space
debug3: key_read: no space
debug3: key_read: no space
debug3: key_read: no space
debug3: key_read: no space
debug3: key_read: no space
debug3: key_read: no space
debug3: key_read: no space
debug3: key_read: no space
debug3: key_read: no space
debug2: key_type_from_name: unknown key type '-----END'
debug3: key_read: no key found
debug1: identity file /home/cjohnson/.ssh/id_rsa type 1
debug3: Not a RSA1 key file /home/cjohnson/.ssh/id_dsa.
debug2: key_type_from_name: unknown key type '-----BEGIN'
debug3: key_read: no key found
debug3: key_read: no space
debug3: key_read: no space
debug3: key_read: no space
debug3: key_read: no space
debug3: key_read: no space
debug3: key_read: no space
debug3: key_read: no space
debug3: key_read: no space
debug3: key_read: no space
debug3: key_read: no space
debug2: key_type_from_name: unknown key type '-----END'
debug3: key_read: no key found
debug1: identity file /home/cjohnson/.ssh/id_dsa type 2
debug1: Remote protocol version 2.0, remote software version Sun_SSH_1.1.4
debug1: match: Sun_SSH_1.1.4 pat Sun_SSH_1.1.*
debug1: Enabling compatibility mode for protocol 2.0
debug1: Local version string SSH-2.0-Sun_SSH_1.1.2
debug1: use_engine is 'yes'
This was working until yesterday and I have made no changes to the systems.
Further information. This is using the stock Solaris ssh client. I also have the openssh client on the system in question and that works.
Just can't figure out what is going on.
Something must have changed. Issues are just the results of one or more causes
Well, for starters, can you delete the private key and generate new public/private key and check? (to be honest if there was key mismatch, it would prompt you for password; should not hang)
Also, check if DNS is enabled in the remote machines's ssh config. If so, is you DNS server responding to the queries properly?
Does it happen while connecting from a particular server?
Hi,
We just built a new Solaris 10 zone. And would like to add it to our DNS server. Its also Solaris 10. Please let me know how can I get the IP resolved using this DNS server. I added entry into zone config file but not working. I did restarted the DNS services. And also added nameserver name... (5 Replies)
I have a server with 6 Ethernet ports. 4 are the the motherboard based 1 GBE ports and 2 are 10 GBE ports on NICs.
I have set these all up with static IP addresses and use the standard /etc/nsswitch.files. My IP addresses are
net0 192.168.1.82
net1 192.168.2.82
and so on till
net5... (4 Replies)
Anyone ever see an issue where ufsdump 'hangs' after the IV Pass?
Normally, it will update with an estimate of how long it will take to complete...and update the info every 20 minutes.
I'm running the following command:
root# ufsdump 0f - /fsmount | ( cd /zfs/newfsmount ) ; ufsrestore rf - )... (2 Replies)
Power server up runs through diagnostics.
Goes to the boot section and then the bit where the cursor is spinning and thats it. Hangs completely.
Any ideas? (10 Replies)
Solaris 10 (Sun V210) System hangs every couple of months. Have to go into ALOM to reset. I did a consolehistory report and seen this in it.
Failed to exec inetd_start method of instance svc:/network/bootps/udp:default: I/O error
WARNING: /pci@1c,600000/scsi@2 (glm0):
Resetting... (3 Replies)
Hi,
I am unable to login into my terminal hosting Solaris 10 and get the below error message
"Server refused to allocate pty
ld.so.1: sh: fatal: libc.so.1: open failed: No such file or directory "
Is there anyways i can get into my machine and what kind of changes are required to be... (7 Replies)
Hi!
I have two solaris 10 machines(say 10.1.1.1,10.1.1.2). i have installed rsync on 10.1.1.2,
10.1.1.1:::
Sun Microsystems Inc. SunOS 5.10 Generic January 2005
-bash-3.00$ ssh 10.1.1.2 "echo $PATH"
Password:... (4 Replies)
Greetings!
I just managed to install Solaris 10 on a Sparc based machine. However, there might be a problem with the way ssh is configured.
I CAN ssh from the machine into another on the network (same subnet, as root), but then the newly installed machine CANNOT seem to accept incoming ssh... (2 Replies)
Hi all,
I have a SUN server Sun-Fire-V890 running solaris 9, with a remote system console .
Both the IP adresses of the server and the console are in a private network (address 10.67.xxx).
For some reasons I need to give the access to the server from outside address 194.xxx, but I prefer that... (2 Replies)
I am currently setting up rdiff-backup to use ssh to connect and remotely backup and retrieve data. I am doing so by creating rsa keys for each server and copying the relevant key to the /.ssh folder on the relevant server.
All seems to work well when severs running solaris 8 with ssh 3.6.1 are... (6 Replies)
02-23-2012
