Sun Cluster switching issue


Login or Register for Dates, Times and to Reply

 
Thread Tools Search this Thread
# 1  
Sun Cluster switching issue

I have installed sun cluster 3.2 on two sprac servers. Configured a failover resource group. Added a LogicalHostname resource to it. LogicalHostname is also added to /etc/hosts with ip address.
I am able to access cluster by share ip used for logical hostname but when i try to switch the resource to other node of cluster, the resource go offline on both node and never switch.

Any help ...
Login or Register for Dates, Times and to Reply

Previous Thread | Next Thread
Thread Tools Search this Thread
Search this Thread:
Advanced Search

9 More Discussions You Might Find Interesting

1. Solaris

Sun cluster v3.2 - Is this right?

Running Sun Cluster v3.2 it appears. Two clustered physcial servers both running Solaris 10. Both servers run a number of Oracle DBs etc. BUT I'm a bit concerned that its been set up but will never switch in the even of failure of one of the hosts? Some of the cluster groups we've... (3 Replies)
Discussion started by: psychocandy
3 Replies

2. Red Hat

Switching services from active node to failovernode in cluster

Hi All, I was asked to Switch the service from failover to active node as we need to reboot active node for regular maintenance. Unfortunately our senior admin left the organization. It would be helpful if some one answer this query. Detailed info with steps will be appreciated. Here are... (1 Reply)
Discussion started by: vamshigvk475
1 Replies

3. Solaris

Sun Cluster 3.2 Issue

Hello everyone, I have two Solaris 10 servers that are on cluster. The cluster is a Sun Cluster 3.2 I have a script cronned that stop/start a ressource in a resource group everyday. Today I have checked the status of the ressources and I found that my ressource group have a "Error--stop... (1 Reply)
Discussion started by: adilyos
1 Replies

4. Solaris

Sun cluster 4.0 - zone cluster failover doubt

Hello experts - I am planning to install a Sun cluster 4.0 zone cluster fail-over. few basic doubts. (1) Where should i install the cluster s/w binaries ?. ( global zone or the container zone where i am planning to install the zone fail-over) (2) Or should i perform the installation on... (0 Replies)
Discussion started by: NVA
0 Replies

5. Solaris

Sun Cluster configuration issue

I am using VMware Workstation-7 on Windows-XP host . I am trying to configure Solaris 10-X86 guest os based 2 nodes Sun Cluster . I have added one extra Virtual Lan adapter on my VMware with another subnet (that I would like to put for SUN Cluster private communication). I have... (0 Replies)
Discussion started by: sanjee
0 Replies

6. Solaris

Sun cluster and Veritas cluster question.

Yesterday my customer told me to expect a vcs upgrade to happen in the future. He also plans to stop using HDS and move to EMC. Am thinking how to migrate to sun cluster setup instead. My plan as follows leave the existing vcs intact as a fallback plan. Then install and build suncluster on... (5 Replies)
Discussion started by: sparcguy
5 Replies

7. Solaris

Sun Cluster

Hi All I hav working knowledge on solarois 10. Could anyone suggest me any doc or material for learning SUN cluster from scratch. Anything from basic level . Thanks in advance!! (1 Reply)
Discussion started by: ningy
1 Replies

8. Solaris

sun cluster

hi can u please send me how to configure cluster in x86 machines. i am using VM ware. Is there any difference in X86 and SPARC cluster installations please help me thaks to all (1 Reply)
Discussion started by: sijocg
1 Replies

9. High Performance Computing

SUN Cluster Vs Veritas Cluster

Dear All, Can anyone explain about Pros and Cons of SUN and Veritas Cluster ? Any comparison chart is highly appreciated. Regards, RAA (4 Replies)
Discussion started by: RAA
4 Replies
scconf_transp_adap_ce(1M)				  System Administration Commands				 scconf_transp_adap_ce(1M)

NAME
scconf_transp_adap_ce - configure the ce Sun Ethernet transport adapter DESCRIPTION
Note - Beginning with the Sun Cluster 3.2 release, Sun Cluster software includes an object-oriented command set. Although Sun Cluster software still supports the original command set, Sun Cluster procedural documentation uses only the object-oriented command set. For more infor- mation about the object-oriented command set, see the Intro(1CL) man page. You can configure ce adapters as cluster transport adapters. These adapters can be used with transport types dlpi. The ce adapter is VLAN capable. A ce adapter connects to a transport switch or to another ce adapter on a different node. In either case, the connection is made through a transport cable. When a transport switch is used and the endpoints of the transport cable are configured by using scconf, scinstall, or other tools, you are asked to specify a port name on the transport switch. You can provide any port name, or accept the default, as long as the name is unique for the switch. The default is to set the port name to the node ID hosting the adapter at the other end of the cable. There are no user configurable properties for cluster transport adapters of this type. SEE ALSO
Intro(1CL), clinterconnect(1CL), clnode(1CL), scconf(1M), scinstall(1M), ce(7D) Sun Cluster 3.2 4 May 2006 scconf_transp_adap_ce(1M)

Featured Tech Videos