V890 serial console inaccessible


 
Thread Tools Search this Thread
Operating Systems Solaris V890 serial console inaccessible
# 1  
Old 10-13-2011
V890 serial console inaccessible

I am battling to get a V890 up and running. The system appears to have AUTOBOOT=false, so no OS comes up when it's powered on, and I do not have the credentials to get to the RSC management console. Output to ttya serial console ends at "Probing I/O buses", I assume because output is then being directed to the RSC card. Here is what I have tried;

- boot system with key in diagnostic position
- emulated Stop-N functionality via the press power button twice when Fault LED blinks rapidly method
- removed RSC card and booted

I have performed the above multiple times, I am still getting no output to ttyya serial console beyond "Probing I/O buses". If only RSC setup could be wiped..... Any ideas would be greatly appreciated.
# 2  
Old 10-13-2011
booting in "diag" mode or removing the rsc card should redirect the output to the ttya port on the server. are you sure, you've the right cable for a serial connection? if i remember right, you'll need a "null modem" cable to connect to the 25pin port...

(the "diag" mode statement is only true with firmware higher than 4.15.x; removing of rsc card should always work)
# 3  
Old 10-13-2011
I just tried the diag boot with RSC card removed, output ends at;

Code:
Probing I/O buses
/pci@8,600000: Device 1 network
/pci@8,600000: Device 2 SUNW,qlc fp disk
/pci@8,700000: Device 1 ide disk cdrom
/pci@8,700000: Device 2 Nothing there
/pci@8,700000: Device 3 Nothing there
/pci@8,700000: Device 4 Nothing there
/pci@8,700000: Device 5 Nothing there
/pci@9,600000: Device 1 Nothing there
/pci@9,600000: Device 2 Nothing there
/pci@9,700000: Device 1 network usb
/pci@9,700000: Device 2 Nothing there
/pci@9,700000: Device 3 Nothing there
/pci@9,700000: Device 4 Nothing there

Does the fact that I see output fine up to that point confirm the serial cable setup I'm using is OK? It's a 25-pin to RJ45 adapter, then to USB on my laptop. I'll pursue the null modem cable suggestion.
# 4  
Old 10-13-2011
can be the cable which allows you to see output but not to make any input...

https://en.wikipedia.org/wiki/Null_modem
# 5  
Old 10-14-2011
DukeNuke2, you sir, are a saviour. I thought I was good on my cabling, but after resurrecting a few items from the closet, bingo, it all magically appeared before my eyes on ttya.

What a great Friday morning, now I can make social plans for the weekend! Thanks so much, again.
Login or Register to Ask a Question

Previous Thread | Next Thread

9 More Discussions You Might Find Interesting

1. Solaris

$ Prompt on Serial console is not responding.

Hi Experts. i have been stuck up with an issue. i have connected my Solaris 8 , Sun fire V445 on serial port by using Teraterm. Initially i was able to login and executed some tasks. After executing some commands (mainly Control +c), i am not able to type any key or not able to do anything at... (2 Replies)
Discussion started by: siddulamadhu
2 Replies

2. Solaris

How to setup a serial console?

i am running solaris 10 in my vmware workstation. How to setup a console for my solaris box. in Vmware i could see a serial port option. can some one help me on how i can setup a console . (0 Replies)
Discussion started by: chidori
0 Replies

3. UNIX for Dummies Questions & Answers

IP Console Vs Serial console.

Hi Gurus, Can some one explain me the difference between a IP console and a serial console. (1 Reply)
Discussion started by: rama krishna
1 Replies

4. Solaris

PPPD on ttya with serial console...?

Hi. I am very very new to Solaris. I found an abandoned Sun Blade 150. I created a 3-wire null modem cable, connected it to an abandoned laptop and successfully installed Solaris 10 using the serial port. This laptop doesn't have ethernet. So I want to establish a PPP connection. Part of the... (2 Replies)
Discussion started by: neutronscott
2 Replies

5. Solaris

Sun Fire V890 - Unable to access RSC or Serial console

Hello Folks, I am having trouble to login to rsc or serial console of V890. The rsc2.2.3 has been configured with required parameters, resetrs and even rebooted. When serial port is connected to laptop, The hyper terminal does not get the console or POSt messages when the server is rebooting... (8 Replies)
Discussion started by: defflepord
8 Replies

6. OS X (Apple)

Use a Serial Console with Mac OS X Leopard

I'm trying to use an old Commodore 128D as a terminal to access OS X's shell via a serial port. I've used 'screen' and 'zterm' to ensure the two machines are successfully interfaced. Instructions for opening up the serial console on other Unix-y operating systems don't work with OS X Leopard. ... (3 Replies)
Discussion started by: joecassara
3 Replies

7. Solaris

Ultra 5 serial console problem

Hi I have a stupid problem with ultra 5 console connection. I can't connect to serial port with my laptop. I made these configurations from ok prompt: OK setenv input-device ttya OK setenv output-device ttya OK setenv auto-boot? false I tried to connect to machine with cisco rollover... (5 Replies)
Discussion started by: noizer`
5 Replies

8. HP-UX

serial console hangs

I have a HP Visualize C200 running hpux that I am trying to boot into using a null modem through com1 from my Sun Ultra 10. I get all the way to the login prompt and then it becomes innactive and wont let me access the machine anymore. Any ideas? (2 Replies)
Discussion started by: trajek
2 Replies

9. AIX

Installing via serial console

I'm stuck - when I boot the machine and hit 5 on the keyboard, all I get is an SP login. Can someone give me some tips on how to get to the install via the serial port? (2 Replies)
Discussion started by: tb0ne
2 Replies
Login or Register to Ask a Question