10 More Discussions You Might Find Interesting
I'm looking to copy a boot disk on an old Solaris 8 system using dd. I'll bring the system down to single user mode and begin from there. I'm copying my source disk to a larger target disk. Do I need to do anything other than the 'dd' command below because the target disk is bigger? ... (2 Replies)
Discussion started by: sparcman
I have noticed that when I copy files to flash disk and in UI I see message copy completed in notification area on task bar, usually copy is not completed. So, if I eject the media I loose data.
It is very serious problem because may cause loss of valuable and even critical data.
Moreover, when... (2 Replies)
Discussion started by: netwalker
3. Shell Programming and Scripting
Hi, How can I unmount an usb disk using the command umount? (3 Replies)
Discussion started by: Guccio
4. UNIX for Dummies Questions & Answers
I have found a question from the exercises of my study mat. The question is
"Why are there a in-core copy and a disk-copy of i-node block and super block?"
If any one know the proper answer then please send me..... (1 Reply)
Discussion started by: dearanik
5. UNIX for Dummies Questions & Answers
Can anybody help me with how I can connect a usb pendrive or external disk to a Sun Server which runs on Solaris 9? I am able to connect the usb drive to a windows server easily and copy files but am wondering if it is possible to do that with Solaris.
Any help will be appreciated. thanks. (3 Replies)
Discussion started by: rahmantanko
SCO Unix ver 5.07
How do I copy files onto an USB memory stick?
Is SCO Unix ver 5.07 able to handle USB memory devices? (2 Replies)
Discussion started by: Schnell
SCO 5.07: How do I copy files to a USB memory stick?
The stick is formatted as a hd and has an active Unix partition using the hole stick for Unix.
How do I get acces to the stick? (1 Reply)
Discussion started by: pschnell
I have a 1TB hard disk that I had partitioned on a Sun clone and had 7 partitions of 137GB a piece. (Using a USB to SATA adaptor)
I then had loaded a new hard disk on my laptop (T60...Lenova) with Solaris 10 X86. I tried to mount the hard disk but it kept telling me the mount point was busy and I... (2 Replies)
Discussion started by: mndavies
9. Shell Programming and Scripting
I am a trying to write a script using a loop i guess. What I need to do is write a script that can allow my users to load a tape and copy a range of files from a tape to the hard disk. By range I mean, I would like the users to pick a range of numbers like files 3 - 8 and the script will... (0 Replies)
Discussion started by: msjazzie
10. Shell Programming and Scripting
How would I write a script to copy a USB key? (1 Reply)
Discussion started by: jo calamine
EHCI(4) BSD Kernel Interfaces Manual EHCI(4)
ehci -- USB Enhanced Host Controller driver
ehci* at cardbus? function ?
ehci* at pci? dev ? function ?
usb* at ehci?
The ehci driver provides support for the USB Enhanced Host Controller Interface, which is used by USB 2.0 controllers.
EHCI controllers are peculiar in that they can only handle the USB 2.0 protocol. This means that they normally have one or more companion
controllers (i.e., ohci(4) or uhci(4)) handling USB 1.x devices. Consequently each USB connector is electrically connected to two USB con-
trollers. The handling of this is totally automatic, but can be noticed since USB 1.x and USB 2.0 devices plugged in to the same connector
appear to connect to different USB busses.
cardbus(4), ohci(4), pci(4), uhci(4), usb(4)
The ehci driver appeared in NetBSD 1.6.
The support for hubs that are connected with high speed upstream and low or full speed downstream (i.e., for transaction translators) is lim-
Aug 10, 2008 BSD