Login or Register to Ask a Question and Join Our Community


Solaris

probe-scsi-all hangs - not returning anything

Login to Discuss or Reply to this Discussion in Our Community

 
Thread Tools Search this Thread
Operating Systems Solaris probe-scsi-all hangs - not returning anything
# 8  
Old 05-09-2011
thnx for all the help...

Here is how I resolved the problem of course with Duke's helpSmilie....hope it helps if someone faces the same issue...

the server was connected to an emc storage and a tape library both through FC...

First i removed both of them and ran probe-scsi-all... it worked fine...
Then i connected the emc storage and again ran probe-scsi-all..worked fine...
Next connected the tape library and ran probe-scsi-all...problem a plenty..stuck again...

SO i disconnected the tape library and rebooted it..
Powered off the server , connected the tape library..
powered on, went to OK prompt and ran probe-scsi-all... a
And everything started working was it shud be Smilie..

Thanks
# 9  
Old 05-09-2011
nice work!
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. Solaris

Help Explain the output of probe-scsi

Can anyone explain the output of probe-scsi command below? ok probe-scsi Target 0 Unit 0 Disk SEAGATE ST373207LSUN72G 045A Target 1 Unit 0 Disk SEAGATE ST373207LSUN72G 045A I have no idea what it means. I tried to read online but I still did not understand. I appreciate... (6 Replies)
Discussion started by: cjashu
6 Replies

2. Shell Programming and Scripting

Network probe script

Hi. I just wrote my first shell script, it’s very ugly but it works. I was wondering if someone could help me clean it up a bit. Original Problem: Current command-line tool (FIND-NEIGHBORS.exe) outputs MAC addresses of neighboring wireless devices. I need the IP address instead;... (0 Replies)
Discussion started by: skeller
0 Replies

3. Shell Programming and Scripting

Network probe script

Hi. I just wrote my first shell script, it's very ugly but it works. I was wondering if someone could help me clean it up a bit. Original Problem: Current command-line tool (FIND-NEIGHBORS.exe) outputs MAC addresses of neighboring wireless devices and I need the IP address instead;... (0 Replies)
Discussion started by: skeller
0 Replies

4. High Performance Computing

What does the 'probe' do in VCS?

Weird question I know, but I'm intrigued. Say for instance you have an Application in an SG with the usual start/stop/monitor. To successfully probe does it just check for existence of the script/file ? Thanks... (1 Reply)
Discussion started by: itsupplies
1 Replies

5. BSD

PROBE not find the device ID

Hi All, Probe is not returning the Device ID, while device (PCI Express-to-PCI Bridge) is already detected by "lspci". I checked this with printing all the device ID which has been detected. Can anyone give me any suggestion or solution. Thanks (in advance) Appu (2 Replies)
Discussion started by: appu
2 Replies

6. Solaris

probe-scsi => error

i have a new netra 240 server when i make probe-scsi in obp i have this output : ERROR: /pci@1c,600000: Last Trap: Fast Data Access MMU Miss am upgarading obp firmware but the problem is always here the os solaris 10) is installed correctely and i can use it , when i type #format i can see... (2 Replies)
Discussion started by: lid-j-one
2 Replies

7. Solaris

Help probe-scsi-all

I have run init 0 to bring it to OK prompt. I know that probe-scsi-all can hang the system. I want to know what is the difference between probe-scsi-all and probe-scsi. I was told that probe-scsi-all external and internal devices and probe-scsi shows only internal devices. what dose this ... (3 Replies)
Discussion started by: nitinkgoud
3 Replies

8. Solaris

probe-scsi-all hangs probing D1000

Hi folks, I´m having a problem with a Ultra60 box with diff scsi pci card conected to one D1000. The conection are correct because a checked the D1000 guide. When a do probe-scsi-all in the OBP, the D1000 blink all disks one time then the led of one of the disks powers off and then nothing... (2 Replies)
Discussion started by: spacewalker
2 Replies

9. Solaris

solaris booting to probe menu

Hi all, everytime the sun fire server reboots in always boots to the probe menu. This needs to be manually booted by command named boot. Is there a boot file somewhere on the system that changes the boot script to boot fully not to the probe menu. (2 Replies)
Discussion started by: dennisca
2 Replies

10. UNIX for Dummies Questions & Answers

probe software

can anyone point me towards a program to list what's installed on my sunOS box and their version numbers. (2 Replies)
Discussion started by: sphiengollie
2 Replies
Login or Register to Ask a Question