10 More Discussions You Might Find Interesting
1. Solaris
Hi All,
I have an Oracle M4000 server with Solaris 10 OS. I have access to Solaris root prompt.
But I don't know the XSCF IP of this server.
Is there any way to display XSCF IP from Solaris OS? (2 Replies)
Discussion started by: byrusber
2 Replies
2. Solaris
Hi Gurus
Can someone help me in explaining the below outputs .
psrinfo -p
4
/usr/sbin/psrinfo -pv
The physical processor has 4 virtual processors (0-3)
SPARC64-VI (portid 1024 impl 0x6 ver 0x93 clock 2150 MHz)
The physical processor has 4 virtual processors (8-11)
SPARC64-VI... (3 Replies)
Discussion started by: ningy
3 Replies
3. Solaris
Hello,
I'm set to go out to our M4000 to reset the XSCF password, since the person who set it up doesn't remember what password they setup.
I have all the steps, but the only question I can't find an answer to is around the mode switch. Right now, based on prtdiag, the mode switch is in... (2 Replies)
Discussion started by: QuickNull
2 Replies
4. Solaris
Hi Guys and Gals,
Does anyone know how to track down a faulty DIMM on the memory board of an M4000?
showhardconf tells me which board it is, but was wondering if there was a way to track it down to a DIMM?
Thanks in advance
Martin (5 Replies)
Discussion started by: callmebob
5 Replies
5. Solaris
Dear Team,
This time i am facing some problems in Sun SPARC M4000 server. I have a doubt, when we are upgrading the firmware if XSCF , the OBP is also upgraded.
What about server OBP, Is that upgardation need to be done separately ?
what about DVD-ROM, HARD DISK firmware.... (3 Replies)
Discussion started by: sudhansu
3 Replies
6. Solaris
Hii All
I was building two M4000 servers and one was successfully installed.
Other one /usr has been unmounted. my putty session got disconnected and i connected to console where it asked for root single maintence
#
# init 0
not foung
# df -h
not found
#
xscf>poweroff -a
xscf>... (8 Replies)
Discussion started by: seems
8 Replies
7. Solaris
Hi Guys and Gals,
Can someone help me possible?
Trying to power up an M4000 and it comes up with xscf fault (reason=0) it then just hangs there.
Any help would be gratefully appreciated.
Thanks
Martin (4 Replies)
Discussion started by: callmebob
4 Replies
8. Solaris
Hi everyone,
I wanted to ask a question about fmadm and explorer outputs.
Recently found out that an error shows up in fmadm saying "mb is faulty but still in service" so we took an explorer send to Oracle Support. Error led wasn't on but we didn't want to risk the probability.
They came up... (1 Reply)
Discussion started by: royalliege
1 Replies
9. UNIX for Dummies Questions & Answers
I'm trying to power on our SUN m4000 server after a recent shutdown. When I try to connect to the xscf console I'm getting prompted for a password. The system is not asking for a login just a password. Below is the output from the xscf console.
Anyone know how I can safely get back to the... (0 Replies)
Discussion started by: orahi001
0 Replies
10. Solaris
Hi Guys,
Anyone know any commands to verify the graphics card is installed correctly on an M4000?
show-displays just comes back and echoes nothing.
Also there is on input-device or output-device variable when you run printenv.
This in itself is worrying.
Any advice would be... (4 Replies)
Discussion started by: callmebob
4 Replies