How to enable hba port of a two port hba card

10 More Discussions You Might Find Interesting

1. Solaris

Solaris 10: how to disable an unused HBA card

Dear all, I have a new Oracle Blade X4-2B server, running Solaris 10. The server comes with a HBA card that will not be used now. It has not fibers connected to it. As a consequence, its leds never stop flashing. My question is: how to disable this HBA card, without removing it physically...

2. Solaris

How to find port number wwn of particular port on dual port HBA,?

please find the below o/p for your reference bash-3.00# fcinfo hba-port HBA Port WWN: 21000024ff295a34 OS Device Name: /dev/cfg/c2 Manufacturer: QLogic Corp. Model: 375-3356-02 Firmware Version: 05.03.02 FCode/BIOS Version: BIOS: 2.02; fcode: 2.01;...

3. Red Hat

HBA card faulty

Hi, How to determine if HBA card in getting faulty from linux host ? any pointers.

4. Solaris

Which FC HBA card support Solaris9

I have JNI FCE-6460-N fc card , it is detected in OK prompt.....I connected Sun StorEDGE A5000 FC storage. in OK prompt, PROBE-SCSI-ALL showing A5000 fc hdds details in ok prompt..... but in OS level.....not showing the hdd, i tried in DEVFSADM command and FORMAT command not showing A5000...

5. Solaris

How to enable Serial port on ILOM, when Network Port is enabled in parallel

Hi Everyone, In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected...

6. Solaris

Few things related to HBA port & fcinfo command

Hi Gurus I need to know few things related to HBA port & fcinfo command I have a server where there are 4 HBA ports cards are their. Out of 4 ports 2 are in use & 2 are not in use when I check it physicall. Now I want to know the command through which I can get information about all above...

7. Solaris

Solaris 10. fcinfo hba-port shows adapter not Found

I understand that fcinfo hba-port should show information(WWN, HBA vendor, etc..) but my result show "No adapter found". If I used grep -i 'version' /var/adm/messages* then I see my installed HBA (QLogic FCode at 2.00.09).. I am wondering why and what I had failed to install? Thanks in advance....

8. IP Networking

4GB Dual Port HBA

I have one 4GB, dual port HBA. Is each port rated for 4GB, or is it the whole HBA rated for 4GB? Also, how do I determine which is port0 / port1 with "lscfg -vl fcs0" command. Thanks.

9. AIX

Need HBA card driver

Hi All, SUN emulex HBA card has been installed on P520 box. When i run the cfgmgr i am getting the following message. lpar2#cfgmgr cfgmgr: 0514-621 WARNING: The following device packages are required for device support but are not currently installed....

10. Solaris

HBA Card

Hello...I got a problem here. I have HBAs installed in one of the domains in E20 and I gotta find out the brand and firmware. But when I do a prtconf, I cannot see the HBA. For other servers installed with HBAs, when I do prtconf on them I can see either qlc or em. Can you guys enlighten me how to...

LEARN ABOUT NETBSD

iy

IY(4)							   BSD Kernel Interfaces Manual 						     IY(4)

NAME

     iy -- Intel EtherExpress PRO/10 Ethernet driver (Intel i82595)

SYNOPSIS

     iy0 at isa? port {port} irq ?

DESCRIPTION

     The iy device driver supports the EtherExpress PRO/10 card, and might support other ISA cards using the same chip.

MEDIA SELECTION

     The different models of the supported boards come with some subset of RJ-45, BNC and AUI connectors.  Supported media include:

	   AUI/DIX     Standard 15 pin connector

	   10Base2     BNC, also known as thin-net

	   10BaseT     UTP, also known as twisted pair

     The default port to use is the port the card autodetects at ifconfig up time.  To choose an alternative port, an explicit medium can be spec-
     ified to ifconfig(8) or in your ifconfig.iy? file.

NOTES

     The EtherExpress PRO card has no jumpers to set the address.  Intel supplies software to set the address of the card in software.	You have
     to hardwire this address in your kernel configuration file.

SEE ALSO

     ed(4), eg(4), el(4), ep(4), intro(4), ix(4), le(4), ifconfig(8)

STANDARDS

     are great.  There's so many to choose from.

BSD
								   May 22, 1996 							       BSD

Solaris