10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
Hello scripting geeks,
I am new to scripting and facing some issues in writing the logic of the script. Request your kind help here
Actually when i run a command i get o/p as below
o/p :
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
these are hex values i guess...now i want to... (15 Replies)
Discussion started by: kulvant29
15 Replies
2. Red Hat
I need to add a VMware virtual disk to the 99-oracle-asmdevices.rules file but the OS is not assigning a WWID to the disk. It has been fdisk'd and a single partition created.
What TAG inside the file needs to be added? the Program scsi-id does not work for some reason. latest patches... (0 Replies)
Discussion started by: mrmurdock
0 Replies
3. Solaris
Hi all,
Is there anyway i can control the naming of the disk device ?
I have added an iscsi disk on server1 using iscsiadm , devfsadm and it is now showing as
/dev/dsk/c2t0d0 in node1
However, i am worried that the same disk will appear as
/dev/dsk/cXtXd0 in node2
This iscsi disk(lun)... (0 Replies)
Discussion started by: javanoob
0 Replies
4. Solaris
Hi,
This is Solaris-10 box and in few of file-system (root file-system of non global zones), usage/available is not showing correct size. I am not able to figure out, what is eating up this space.
Global Server - bdrpod01
Non Global zone - bdrpod01-zputq01
root@bdrpod01:/root# df -h... (2 Replies)
Discussion started by: solaris_1977
2 Replies
5. HP-UX
Hi,
I wanted to configure new iscsi port on HPUX system, i added the target port address and configured it, once done, went to array side and searched for that host iqn number , but was nt able to find the same, came to host, then when i ran "iscsiutil -pVS" command it gave me below result
... (0 Replies)
Discussion started by: Vinay Kumar D
0 Replies
6. UNIX for Advanced & Expert Users
Hello,
in one default UFS filesystem we have 8K block size (bsize) and 1K fragmentsize (fsize). At this scenary I thought all "FileSytem IO" will be 8K (or greater) but never smaller than the fragment size (1K). If a UFS fragment/blocksize is allwasy several ADJACENTS sectors on disk (in a ... (4 Replies)
Discussion started by: rarino2
4 Replies
7. Shell Programming and Scripting
Hi All,
OS: Linux 86x64 bits Red Hat Linux
I get the email alert for the following when Alert condition is set for 30:
/dev/sda1 99M 21M 74M 22% /boot
-> Below 30%(Should not get the email alert)
Expected output as per E-Mail alert:
/dev/sda3 20G ... (2 Replies)
Discussion started by: a1_win
2 Replies
8. AIX
Hi All,
Recently I'm taking my first steps in AIX, initially with no real issues. Until now, off course...
I hooked up a couple of iSCSI disks to the system, with a RHEL5 machine running tgt on the other side. When running cfgmgr after initial configuration, I got an error:
# cfgmgr -l... (4 Replies)
Discussion started by: mr.aart
4 Replies
9. Solaris
So I just tried what somebody here suggested and set up my backupserver with a zraid2 over 16 disks (4x4 groups)
zpool create tank raidz2 c7t0d0 c7t1d0 and so on.
zpool list showed a correct info about 5,4T in size (I did not use all disks), but when I did a df -h, it showed me only half the... (5 Replies)
Discussion started by: PatrickBaer
5 Replies
10. SCO
New IBM x3400 machine with a raid 5 configuration. Go through the early setup routine to the point where I answer the questions for time zone, machine name. Enter continue and get a message stating :
"Incorrect disk partitioning cannot continue" This is a sco message, refers to the installation... (1 Reply)
Discussion started by: wjbtms
1 Replies