Add new disk to Sun StorEdge 3310 RAID


Login or Register for Dates, Times and to Reply

 
Thread Tools Search this Thread
Operating Systems Solaris Add new disk to Sun StorEdge 3310 RAID
# 1  
Add new disk to Sun StorEdge 3310 RAID

HI guys.
Bit of a noob so bear with me.

I have 2 new disks I want to add to my StorEdge 3310 but am getting lost in the steps. We have another 3310 (JBOD) that I was able to plug the disks into and they instantly showed up. Did a few minor commands after (drvconfig, devfsadm etc..) and I was good to partition the slices...

On our 3310 (RAID) I plugged them in and its not seeing them:

Code:
 
# format
Searching for disks...done
 
 
AVAILABLE DISK SELECTIONS:
       0. c1t0d0 <SUN36G cyl 24620 alt 2 hd 27 sec 107>
          /pci@9,600000/SUNW,qlc@2/fp@0,0/ssd@w21000004cfd967a7,0
       1. c1t1d0 <SUN36G cyl 24620 alt 2 hd 27 sec 107>
          /pci@9,600000/SUNW,qlc@2/fp@0,0/ssd@w21000004cfd964d1,0
       2. c2t0d0 <SUN-StorEdge3310-0325 cyl 35424 alt 2 hd 127 sec 127>
          /pci@8,600000/pci@1/scsi@4/sd@0,0

What steps do I need to perform to allow the server to see the 2 new added disks. (SEAGATES)

Thanks
# 2  
you have to logon to the array...

Contents
# 3  
So can I accomplish that by plugging a laptop into the serial port of the array? I did see some documentation about doing that.

What would the steps be after that?
# 4  
you can use a serial line... but note, the default setting for this device is 38400 bauds! for the steps after connecting, use the documentation... haven't worked on such an array for years...
# 5  
Used serial lin ebut still can't connect with hyperterminal.
Says I am connected and when I type anything just puts x's on the screen...

Any help would be appreciated.

Thanks

---------- Post updated at 01:16 PM ---------- Previous update was at 12:59 PM ----------

K I was able to get to a login screen using baud 9600 but not sure of the id and password. Is there a default one I can use?

---------- Post updated at 02:16 PM ---------- Previous update was at 01:16 PM ----------

Alright making progress.

After a lot of reading about the SCSI 3310 array I have determined there is a single bus configuration. I have added two 72 GB disks to the array and would like to set them up using sccli.

Does anyone know where I can locate that documentation in sun?
Login or Register for Dates, Times and to Reply

Previous Thread | Next Thread
Thread Tools Search this Thread
Search this Thread:
Advanced Search

Test Your Knowledge in Computers #555
Difficulty: Easy
In C, if double b = 3.14159265359; printf("b=%10f ", b); then the output with be b=3.141593
True or False?

9 More Discussions You Might Find Interesting

1. Solaris

Hardware RAID not recognize the new disk [Sun T6320]

We have hardware RAID configured on Sun-Blade-T6320 and one of the disk got failed. Hence we replaced the failed disk. But the hot swapped disk not recognized by RAID. Kindly help on fixing this issue. We have 2 LDOM configured on this server and this server running on single disk. #... (8 Replies)
Discussion started by: rock123
8 Replies

2. Solaris

Move disks to different StorEdge, keeping RAID

Hi. I need to move a 5 disk RAID5 array from a SE3310 box to a different SE3310 array. After installing the disks in the "new" StorEdge device, I "would like" ;) to be able have access to the data which is on the RAID. Essentially, the quesion is, how can this be done? :confused: I checked... (5 Replies)
Discussion started by: alexs77
5 Replies

3. Filesystems, Disks and Memory

Poor read performance on sun storedge a1000

Hello, i have a a1000 connected to an e6500. There's a raid 10 (12 disks) on the a1000. If i do a dd if=/dev/zero of=/mnt/1 bs=1024k count=1000 and then look at iostat it tells me there's a kw/s of 25000. But if i do a dd of=/dev/zero if=/mnt/1 bs=1024k count=1000 then i see only a... (1 Reply)
Discussion started by: mbrenner
1 Replies

4. Solaris

storEDGE A5000 disk Array

Do you know how do I make my solaris 8 detect the storEDGE A5000?. I have problem making it recognise, without that I cannot install VxVM. Any ideas? (7 Replies)
Discussion started by: calsum
7 Replies

5. Solaris

Using Enterprise 4500 with storedge D100 and storedge A5200

Sorry if this seems trivial. i have been given a task at work to configure a sun processing server "enterprise 4500" so it can work with the a storage server "storedge A5200" and "storedge D1000" the truth is i have never worked on a sun server before. i need a guideline (step by step) as to... (5 Replies)
Discussion started by: lawalidowu
5 Replies

6. UNIX for Dummies Questions & Answers

Sun - RAID

From what I have been finding on the net is that most all Sun RAID setups are software? Is it really that uncommon for Sun servers to have hardware RAID? (6 Replies)
Discussion started by: kingdbag
6 Replies

7. UNIX for Advanced & Expert Users

Help: Sun Disk partitioning for Sun V240 & StorEdge 3300

Dear Sun gurus, I have Sun Fire V240 server with its StorEdge 3300 disk-array. Following are its disks appeared in format command. I have prepared its partitions thru format and metainit & metattach (may be i have made wrong steps, causing the errors below because I have done thru some document... (1 Reply)
Discussion started by: shafeeq
1 Replies

8. Solaris

Add new hard disk to sun sparc server?

A sparc server has a new SCSI hard disk added and labeled by the engineer, but they need to be formatted identically to an existing disk (c4t0d0). You decide to script the process and run from the command line without interaction. I know that the following command line must be achieve this. #... (3 Replies)
Discussion started by: kingsan
3 Replies

9. UNIX for Advanced & Expert Users

sun storedge

I just installed sun storedge 3310 connected to a sunfire 280R with a total siz of 680GB and now am trying to create filesystems. issue format command and created my partitions, the largest size of the partition is 170GB. but I try to create new filesystems by using newfs like newfs... (3 Replies)
Discussion started by: hassan2
3 Replies

Featured Tech Videos