USCSICMD ioctl calls for Fibre Channel(FC) devices on Solaris 10?

9 More Discussions You Might Find Interesting

1. Solaris

Issue with Fiber Channel cards in Solaris

hi everone i am experiencing disconnectivity from storage to My database machines. i have doubt on my FC cards in my sparc T4-2 machines. i want to know how should i check from my solaris that whether the cards are ok or not because once the disks get disconnect from SAN so it come back again but...

2. Solaris

Fibre Channel link not ready on Netra 240

Hi, One of my Netra 240 went into hung state and I had to reboot it. I powered it off and tried booting it again but unsuccessful. It is not connected to SAN and have local disks. Not able to boot in failsafe mode too. There are two disks of 72GB, both are mirrored in SVM. It complains about...

3. AIX

[ASK] - AIX Fibre Channel behavior

Hello all, Let me introduce about the context and my environment. We have an AIX 6.1 system, it has 4 FC channels / > lsdev -Cc adapter | grep fcs fcs0 Available 23-T1 Virtual Fibre Channel Client Adapter fcs1 Available 23-T1 Virtual Fibre Channel Client Adapter fcs2 Available 23-T1...

4. Solaris

Fibre channel link down on booting Solaris server

Hi I had power issue that affected a server, in which I had power ON the server SPARC T1-B3 running solaris 10. After power on the system stops at ok prompt, them I issued the following commands: {0} ok setenv auto-boot? false auto-boot? = false {0} ok reset-all SPARC T3-1B,...

5. Hardware

Fibre Channel HBA recommendations?

We will be buying new Xeon E5-based servers for our datacenter and were wondering which Fibre Channel host bus adapters we should select for these. The choices are Emulex or QLogic (8Gb FC HBAs). Anybody have any recommendations on which is the better choice? Thanks in advance.

6. AIX

Power6 Virtual Fibre Channel Adapter

Hello, Searched in all IBM Redbooks and on the internet and couldn't find anything about the new feature of POWER 6 which Virtual Fibre ( Fiber ) channel adapter. It is similar to virtual scsi adapter. In my client partition I created the virtual Fibre Adapter mapped it with the VIO...

7. AIX

Fibre channel drivers on RS/6000 aix 5L

Want to configure IBM raid strorage but the aix 5L cds do not have the drivers for the fibre channels. The machine is RS/6000. I have gone to IBM downlaodable sites but i can't find the drivers? help pliz:mad:

8. IP Networking

Identification of data calls & voice calls

Is there any facility to filter/identify the data calls and voice calls coming throug modem? OR Can we get the data or voice calls information through a script(preferably C Kermit)?

9. Solaris

devices in solaris 10

i want to use the devfsadm command and understand its function

LEARN ABOUT CENTOS

scsieject

scsieject(1)						      General Commands Manual						      scsieject(1)

NAME

       scsieject - control SCSI tape devices

SYNOPSIS

       scsieject [-f <scsi-generic-device>] commands

DESCRIPTION

       The scsieject command controls SCSI devices in a platform-independent manner. As long as 'mtx' works on the platform, so does 'scsieject'.

OPTIONS

       The first argument, given following -f , is the SCSI generic device corresponding to your tape drive.  Consult your operating system's doc-
       umentation for more information (for example, under Linux  these  are  generally  /dev/sg0  through  /dev/sg15,	under  FreeBSD	these  are
       /dev/pass0  through  /dev/passX.  Under Solaris this is usually the same as your tape drive (Solaris has a SCSI passthrough ioctl). You can
       set the STAPE or TAPE environment variable rather than use -f.

COMMANDS

       load	 Load the medium into the drive.  When this command is issued to a CD/DVD drive  and  the  tray  is  extended  the  tray  will	be
		 retracted if the drive is capable of it.

       unload	 Unload  the medium from the drive (also known as eject).  When this command is issued to a CD/DVD drive or a tape drive the media
		 will be ejected if the device supports it.

       start	 Start the device.  Some devices require a start command after a media changer has loaded new media into the device.

       stop	 Stop the device.  Some devices require a stop command prior to unloading the medium from the device when using a media changer.

       lock	 Lock the device.  Locks the device so that the medium cannot be removed manually.

       unlock	 Unlock the device.  Unlocks the device so that the medium can be removed manually.

AUTHORS

       This program was written by Robert Nelson <robertnelson@users.sourceforge.net> based on the scsitape program  written  by  Eric	Lee  Green
       <eric@badtux.org>.  Major portions of the 'mtxl.c' library used herein were written by Leonard Zubkoff.

HINTS

       Under  Linux,  cat /proc/scsi/scsi will tell you what SCSI devices you have.  You can then refer to them as /dev/sga, /dev/sgb, etc. by the
       order they are reported.

       Under FreeBSD, camcontrol devlist will tell you what SCSI devices you have, along with which pass device controls them.

       Under Solaris 7 and 8, /usr/sbin/devfsadm -C will clean up your /devices directory. Then find /devices -name 'st@*' -print  will  return  a
       list of all tape drives. /dev on Solaris is apparently only of historical interest.

BUGS AND LIMITATIONS

       There are no known bugs or limitations.

AVAILABILITY

       This version of scsieject is currently being maintained by Robert Nelson <robertnelson@users.sourceforge.net> as part of the 'mtx' suite of
       programs. The 'mtx' home page  is  http://mtx.sourceforge.net  and  the	actual	code  is  currently  available	there  and  via  SVN  from
       http://sourceforge.net/projects/mtx.

SEE ALSO

       loaderinfo(1),tapeinfo(1),mtx(1)

								   scsieject1.0 						      scsieject(1)

Solaris