10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
Hello.
System : opensuse leap 42.3
I have a bash script that build a text file.
I would like the last command doing :
print_cmd -o page-left=43 -o page-right=22 -o page-top=28 -o page-bottom=43 -o font=LatinModernMono12:regular:9 some_file.txt
where :
print_cmd ::= some printing... (1 Reply)
Discussion started by: jcdole
1 Replies
2. AIX
Anyone running CICS TX in a WPAR ?
In my attempts to run CICS TX 5.1.0.1 in a WPAR..... CICS fails to start due to unable to load a CICS IPC Kernel Extension. The Kernel Extension is 64 bit (so not a 32 vs 64 bit issue).
Base system/LPAR is Power8 and AIX 7.1 TL3 SP5. WPAR is versioned... (4 Replies)
Discussion started by: The Doctor
4 Replies
3. Solaris
I'm posting here as it didn't seem quite right in the hardware section (as it's LOM commands). My apologies if I have that wrong though :)
I've finally gotten round to configuring the LOM on my Netra X1, but I can't get it to change the hostname via the "set" command:
lom>show hostname... (2 Replies)
Discussion started by: Smiling Dragon
2 Replies
4. Shell Programming and Scripting
Hi,
I have line in input file as below:
3G_CENTRAL;INDONESIA_(M)_TELKOMSEL;SPECIAL_WORLD_GRP_7_FA_2_TELKOMSEL
My expected output for line in the file must be :
"1-Radon1-cMOC_deg"|"LDIndex"|"3G_CENTRAL|INDONESIA_(M)_TELKOMSEL"|LAST|"SPECIAL_WORLD_GRP_7_FA_2_TELKOMSEL"
Can someone... (7 Replies)
Discussion started by: shis100
7 Replies
5. Solaris
Hi
i am accessing the server remotly. i want to replace bad dvd writer. how do i know the part number of the dvd drive for raising a spare.
thanks (3 Replies)
Discussion started by: sunnybee
3 Replies
6. AIX
Hi,
This is odd, however here goes. There are several shell scripts that run in our production environment AIX 595 LPAR m/c, which has sufficient memory 14GB (physical memory) and horsepower 5CPUs. However from time to time we get the following errors in these shell scripts. The time when these... (11 Replies)
Discussion started by: jerardfjay
11 Replies
7. Shell Programming and Scripting
Hallo,
i need a Prompting read in my script:
read -p "Enter your command: " command
But i always get this Error:
-p: is not an identifier
When I run these in c-shell i get this error
/usr/bin/read: read: bad option(s)
How can I use a Prompt in the read command? (9 Replies)
Discussion started by: wiseguy
9 Replies
8. Filesystems, Disks and Memory
Dear All,
i have a SCSI hard disk drive i'm installing on it solaris 5 and the workstation is sun sparc, i made an image of this H.D using Norton Ghost 6, so i took off the SCSI H.D from the sun workstation and put it on a Compaq server then i booted the server from the Norton Ghost floppy disk... (0 Replies)
Discussion started by: wesweshahaha
0 Replies
9. Shell Programming and Scripting
Hi,
running a script fine , i get twice the following message and whether i put "set -x" , i don't see what's going wrong :
/users/notes01/scripts/sad/util/verif_boot_notes.ksh: Ma: bad number
any ideas ?
regards
Christian (4 Replies)
Discussion started by: Nicol
4 Replies
10. Solaris
I tried rebooting my Sun server just a few minutes ago and I got the following at boot:
--
Sun Fire 280R (UltraSPARC-III+) , No Keyboard
Copyright 1998-2002 Sun Microsystems, Inc. All rights reserved.
OpenBoot 4.5, 1024 MB memory installed, Serial #xxxxxxxxx
Ethernet address... (6 Replies)
Discussion started by: deckard
6 Replies