I purchased a Sunblade 150 from Ebay. It had 512MB RAM and 80GB hard disk. I recently purchased additional RAM and another 80GB disk, and installed them. The RAM goes through POST without issues. I just can't get beyond the OK prompt. I am using the serial console.
I have been unable to make the on-board graphics work, and do not have a SUN mouse and keyboard. I am content with the serial console. Using the serial console, I can see the machine going through all its various tests...prior to shutting it down, I went to OBP and set the diagnostics flag to true. Everything appears copasetic
Except that I cannot send any data to the serial console. I dug out my RS-232 tester, and it does appear to have a problem. The CD (Carrier Detect), DSR (Data Set Ready), RTS (Ready to Send), DTR (Data Terminal Ready), CTS (Clear to Send), and RD (Receive Detect) lights are lit as normal, however, the TD (Transmit Detect) is not lit.
To check the cable, I connected it to my RS6000/B50 server. All 7 lights come on as expected and everything works. The problem therefore is not my cable, nor is it the XP system that I am using PuTTY to make the connection with. This cable did work prior to the installation of RAM and hard disk. I was able to install Solaris 10 via the serial console without event.
I had to purchase new IDE cables for the upgrade--the ones that came with it were far too short.
This makes no sense to me at all. Should I remove the RAM? I did try it with the 2nd Hard Disk disconnected, but the problem returned.
Why is the Sunblade not asserting TD? Everything else seems just fine.
I read elsewhere that I cannot use a standard mouse and keyboard with this thing. Further, the on-board video is deader than Elvis--at least there is a rumor that Elvis lives. Could these issues be related?
I have used a Sun Blade-150 serial console and all I connect are pins 2, 3, 1 and 7: Serial Port & Cable Pinouts SunHELP
Did you know you can use the serial port for input and the monitor for output (and vice versa)?
The output-device setting can be set to include the resolution and refresh rate of your monitor so that you see the messages during power up and before Solaris takes over, e.g.:
in this case 1024 pixels by 768 pixels at 60Hz.
I have seen folk confused by having two VGA connectors because a framebuffer card had been added in and they had the monitor plugged into the wrong one. To make the alternative framebuffer card may require amending of the pci-probe-list: 9. Multiple Monitors on a System (Solaris Handbook for Sun Frame Buffers) - Sun Microsystems
I'm fairly sure a PC USB mouse will work, it might be a bit fast or slow, a normal PC USB keyboard I think will work but will lack the power, front, back, stop, etc. keys.
On the memory front a Sun Blade-150 requires error correction SDRAM (ECC SDRAM).
Thanks for your input. Unfortunately, I cannot enter anything at the OBP OK prompt. That is the problem. There are not two monitor cards in the machine. There is only the on-board VGA port. Unfortunately, my monitor does not permit manual setup. It is auto-tune only, and when it detects some sort of VGA signal, it will adjust itself to that signal. I have a KVM, and it works fine on the other 3 machines it is connected to; including the HP-UX system which only supports 1024x768 when it boots.
This cable did work fine until I made the upgrades. I installed Solaris 10 without issue, and was able to make StarOffice work for me after it was on the network. But you're correct about the pinouts. I carefully checked the serial connector; there are no bent pins.
I'm beginning to think that the mainboard on this thing is busted. It worked fine with the less RAM and disk before the upgrade. Maybe I did something to it and broke it somewhere along the way.
This sucks; I am out of work and cannot afford a new SunBlade. I need this machine to learn Sun's virtualization and ZFS. These need to be on my resume so I can get some work.
About the keyboard. I would try a standard (PC) usb keyboard and a vga monitor plugged in directly. Most USB PC keyboards will work fine as an input device, I have never had any of the problems others have mentioned when using non-sun keyboards ( other than not having the additional keys ).
I removed the upgraded RAM (it is ECC, non-registered). The upgraded RAM passed the extensive POST checks, so I was sure that the issue was not the RAM. In any case, I removed the upgrades and the problem still repeats.
I tried your trick of using a standard USB keyboard and mouse with the serial console showing. Now the boot process does not continue to the OK prompt, but freezes while probing the PCI busses. It completes the following steps, but freezes after the last:
I note that it did detect the USB keyboard; but it locks up. The keyboard is known to be good (I robbed it from my Ubuntu notebook).
Unplug the USB keyboard and reboot; here is the same section of the POST:
Skipping diagnostic script because diag-script = none
ok
When I unplugged the USB mouse/keyboard and rebooted, the Sunblade finished its boot process to the OK prompt. Its just that, without the TD signal asserted on the TTY, I cannot give it the next command to cause it to load the OS. I am almost convinced now that the motherboard is toast.
I tried your suggestion of plugging the monitor directly into the Sunblade (bypassing the KVM): nothing happened; the on-board video just is not functioning (I didn't check this when I first purchased it; I just used the serial console).
So the score card is: no video; no serial console; no USB keyboard/mouse.
I'll keep playing with it this afternoon, but I suspect that I'll be ordering another one soon. I don't have this kind of money. Does anyone want to make me a brother-in-law deal on a gently used Sunblade 150?
Last edited by Scott; 02-21-2010 at 07:25 PM..
Reason: Code tags
Hi.
I have a Microsystems SunBlade 150
shell# cat /etc/release
Solaris 8 2/02 s28s_u7wos_08a SPARC
shell# uname -a
SunOS HOSTNAME 5.8 Generic_108528-14 sun4u sparc SUNW,Sun-Blade-100
shell# prtconf -F
/pci@1f,0/SUNW,m64B@13:m640
When I join to the only account the server try to... (5 Replies)
In bash, you can do something like this:
#!/bin/bash
echo -n "What is your name? " > /dev/tty
read thename < /dev/tty
How can I do the same in python?
I have a python script that has the following content:
#!/usr/bin/python2.7
import getpass
import sys
import telnetlib
import... (2 Replies)
Good Afternoon,
I'm setting up a SunBlade 2500 using ufsrestoreand have gotten to the point where I have restored the root and usr partitions. However, the machine keeps rebooting, never really coming up. Looking at vfstab, it looks pretty empty- shouldn't I see entries like... (22 Replies)
Good Morning,
I took a mirror drive from one Solaris 9 machine and used it to set up another. After syncing another mirror on the second machine I restarted but I don't get a login screen.
I see a message:The X-server cannot be started on display :0
Also during startup I see:... (8 Replies)
Greetings,
I was in the mood of upgrading my sunblade100 in my bedroom, since I recuperated some RAM from intel servers, and found myself with what seems to not work (I was hoping to pass from 256Mb to 2GB... and then upgrading to solaris 10...)
after this failure I tried with just one 512 MB,... (2 Replies)
Hi everyone this is my first post
I have used linux a couple of times and was impressed, so i bought an old sunblade 1000, just to learn something new.
I cannot get the thing to work! I have tried to install solaris 10 and several types of linux. I am beginning to wonder if i was sold a... (3 Replies)
Hi guys,
I have a SunBlade 2000 that I am trying to configure. It has been configured previously with an IP address, hostname, DNS and so forth. I want to configure it with a new IP address. How can I achieve this? It has been one of the most difficult tasks for me as I am not really... (6 Replies)
Hi all,
I am a newbies here,
Have question regards large hard disk install in SunBlade system.
Can SunBlade 150 support 2 x 160GB (internal IDE) ?
Want to make sure before buy the hard disks.
Anyone had experiences configure large hard disk in SunBlade 150 before ?
In the SunBlade 150... (2 Replies)
I have tried to install the Debian distribution for SPARC processor, but is a pian in the neck trying to boot from cdrom or floppy.
Please can somebody to help me to know the easiest way to boot and install Debian on a SUNBLADE 100 system? or wich is the best way to installed on this system, I... (2 Replies)
hii alll
i have a problem with my sunblade100. when i switch on, no display comes but if i ping from a remote machine its pinging,but iam not able to telent to that sun server,what can be the problem,how can i sort ot this issue
2 thing in usb iam not able to use STOP N (to clear the... (3 Replies)