1.I wish to perform a Jumpstart installation, the client being Ultra 5 Sparc
and jumpstart Server being ultra 20 AMD system.
2.I think i have done all the procedures right, like putting the mac address of Sparc 1 to /etc/ethers, creating sysidcfg file, and profile file:
3.When I issued the boot net - install from sparc and issued the following command from jumpstart server
The jumpstart server hangs after the following line:
4.I googled and find the following link, but could not get a solution: An audience of two.
please help
---------- Post updated at 07:38 PM ---------- Previous update was at 07:35 PM ----------
hi incredible,
thanks for the response.
This is connected via switch.
Please give me 12 more hours as I am not near the systems. Thanks a lot.
one more important thing is that, if i remove the following entry from /etc/hosts of jumpstart server:
then the sparc machine will boot from the server, but it ignores the sysidcfg files and works like a normal installation, asking interactive questions starting from Choose Language, etc.
But if i put the above entry back again, the above problem arises. Something related to the ip resolution...(localhost), that is what the link i provided also says, but i cant understand that...!!
---------- Post updated 10-12-09 at 09:47 PM ---------- Previous update was 10-11-09 at 10:03 PM ----------
Following is the content of /etc/bootpararms:
---------- Post updated 10-13-09 at 05:14 PM ---------- Previous update was 10-12-09 at 09:47 PM ----------
everything looks correct but do have the hostname i stated below
do you have a hostname in /etc for it to look at ?
then you need the ip of the JS server in /etc/hosts
then make sure the followign files are correct in /etc
the ethers file needs the MAC address of the client and the hostname example
when you did ./check did you get a rules.ok file after that?
one thing in your bootparams it is different than what I use but that does not mean much here is mine
hi, deaconf..
thanks a lot for your time in typing these information. I think i have configured those information you have provided, but still it gives the same error. thank you once again.
The above entry is wrong. You need to remove it from your hosts file. 127. is not routable. /etc/hosts should look like this:
As for the client "not reading" sysidcfg:
you don't mention which Solaris 10 revision you are using (I can see it is Solaris 10 from the line you posted from /etc/bootparams).
If it is u4 or higher, you need to add the following line to sysidcfg:
If it is u7 or higher, you need to add the line above plus:
Otherwise miniroot will read your sysidcfg, find it incomplete, then execute the interactive config routine.
system shock, thanks a lot for that information. It works.!!
have a great day, like me.!!
---------- Post updated at 07:41 AM ---------- Previous update was at 07:39 AM ----------
One more doubt..
Is there any directive that can be used in the sysidcfg file to inform the jumpstart client to go to console mode of installation instead of trying to go to the gui mode..?
---------- Post updated at 06:19 PM ---------- Previous update was at 07:41 AM ----------
System Shock... u deserve those honours...
thank u..
I'm trying to use a V210 (sun4u) configured as a jumpstart server to flash install a number of T5220's (sunv4).
The Facts:
V210 - Solaris 10 (September 2010 Release / not patched)
T5220's - Archive's created using prior (unknown) version of solaris 10.
Flar -i <archive name> shows the... (6 Replies)
hi friends,
i dont know how to install jumpstart . i have solaris cds( 5 nos.). i tried to install jumpstart but there is no setup_install_server file. What i want to do for installing jumpstart server
please help me
thanks to all (8 Replies)
Hi all,
I'm having an issue with jumpstart that I haven't seen before. After booting the server and selecting F12 to boot it from the network it finds the jumpstart profile that has been set up for it and proceeds with the build until I get the following error:
SunOS Release 5.10 Version... (4 Replies)
I'm trying to jumpstart my remote server. My /etc/hosts and /etc/ethers files have the correct data. Keep getting the following message at the ok prompt
after running a boot net - install
Link hasn't comeup yet
Ran a test-net and got the following message.
Link is -- down
When... (7 Replies)
Hi Peeps,
Created a jumpstart server for an unattened install and it works, but got 2 bugs in the config which I would like to work out:
when you boot net install
It still asks you to select a language and locale, after you do this it kicks of an unattended install.
So my question is,... (5 Replies)
Hello all,
I configured a jumpstart server ( the server is in the same subnet as the client) and gave boot net - install in the client.
The client boots up shows the banner and then displays error:
cant read disk label
cant open disk label package
and then goes to OK prompt.
What... (1 Reply)
Hi,
Which sites have general information on JumpStart for Solaris 8?
I would like to know more about boot server, installation server, and configuration server.... and all other good things about JumpStart....Thanks..:p
Doo... (2 Replies)