NIC card repetative Failover


 
Thread Tools Search this Thread
Operating Systems Solaris NIC card repetative Failover
# 1  
Old 08-25-2009
Error NIC card repetative Failover

I have configure 2 NIC in ipmp group1 .Similarly other 2 NIC in ipmp group2
When I connect both NIC to 2 different switch , which is connect to one L3 switch as trunk. Both the NIC failover to each other continously.

Following are the message log.

ifmsdb1 in.mpathd[166]: [ID 594170 daemon.error] NIC failure detected on nxge0 of group ipmp1
ifmsdb1 in.mpathd[166]: [ID 832587 daemon.error] Successfully failed over from NIC nxge0 to NIC bge0
ifmsdb1 in.mpathd[166]: [ID 594170 daemon.error] NIC failure detected on nxge8 of group ipmp2
ifmsdb1 in.mpathd[166]: [ID 832587 daemon.error] Successfully failed over from NIC nxge8 to NIC nxge2
ifmsdb1 in.mpathd[166]: [ID 299542 daemon.error] NIC repair detected on nxge0 of group ipmp1
ifmsdb1 in.mpathd[166]: [ID 620804 daemon.error] Successfully failed back to NIC nxge0
ifmsdb1 in.mpathd[166]: [ID 299542 daemon.error] NIC repair detected on nxge8 of group ipmp2
ifmsdb1 in.mpathd[166]: [ID 620804 daemon.error] Successfully failed back to NIC nxge8
ifmsdb1 in.mpathd[166]: [ID 594170 daemon.error] NIC failure detected on nxge0 of group ipmp1
ifmsdb1 in.mpathd[166]: [ID 832587 daemon.error] Successfully failed over from NIC nxge0 to NIC bge0
ifmsdb1 in.mpathd[166]: [ID 594170 daemon.error] NIC failure detected on nxge8 of group ipmp2
ifmsdb1 in.mpathd[166]: [ID 832587 daemon.error] Successfully failed over from NIC nxge8 to NIC nxge2
ifmsdb1 in.mpathd[166]: [ID 299542 daemon.error] NIC repair detected on nxge0 of group ipmp1
ifmsdb1 in.mpathd[166]: [ID 620804 daemon.error] Successfully failed back to NIC nxge0
ifmsdb1 in.mpathd[166]: [ID 299542 daemon.error] NIC repair detected on nxge8 of group ipmp2
ifmsdb1 in.mpathd[166]: [ID 620804 daemon.error] Successfully failed back to NIC nxge8
ifmsdb1 in.mpathd[166]: [ID 594170 daemon.error] NIC failure detected on nxge8 of group ipmp2
ifmsdb1 in.mpathd[166]: [ID 832587 daemon.error] Successfully failed over from NIC nxge8 to NIC nxge2
ifmsdb1 in.mpathd[166]: [ID 594170 daemon.error] NIC failure detected on nxge0 of group ipmp1
ifmsdb1 in.mpathd[166]: [ID 832587 daemon.error] Successfully failed over from NIC nxge0 to NIC bge0 ifmsdb1 in.mpathd[166]: [ID 299542 daemon.error] NIC repair detected on nxge0 of group ipmp1
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. Red Hat

Finding speed of NIC Card

Hi, I would like to know how to find out ACTUAL speed of NIC Card. I have used the command ethtool eth0, it is showing supported modes, but what is acutal speed ? how to find out? (4 Replies)
Discussion started by: manoj.solaris
4 Replies

2. HP-UX

NIC card issue

Hi, Someone asked me the below. If the box has multiple NIC cards, try to run a test with interface address specified as shown below $ java utils.MulticastTest -N server100 -A 237.155.155.1 -i <interfaceaddress> How can I now find out if my box has multiple NIC cards and how can I... (5 Replies)
Discussion started by: mohtashims
5 Replies

3. AIX

AIX -How to find which NIC is on which PCI card

Hi All, How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v Any idea? Thanks. (2 Replies)
Discussion started by: samnyc
2 Replies

4. Linux

How to check which NIC Card is used for backups?

I have a linux box with 2 nic cards on it one for prod and one for backup. My question is while the backup are happening how do I determine which nic is used for backups . I would like to run a command so that that I can see the usage in a dynamic fashion. (7 Replies)
Discussion started by: new2prog
7 Replies

5. Linux

changing speed of NIC Card in linux

Hi, I would like to know how to change the speed of ethernet card in linux? as it is showing auto-neg using mii-tool -v eth0 and my requirement is 100mbps full duplex. Regards, Manoj (3 Replies)
Discussion started by: manoj.solaris
3 Replies

6. Solaris

Reg. NIC card

Hi friends i have problem with my home pc, i installed solaris 10 but my lan drivers are not installed, if i want to install drivers manually from where to download and how to install. I have Realtech lan card. when i type ifconfig -a it shows only localhost 127.0.0.0 Lo0 cannot see other than... (5 Replies)
Discussion started by: kurva
5 Replies

7. HP-UX

how can I determine which NIC card is virtual NIC Card

how can I determine which NIC card is virtual NIC Card which condition can make a decision Does HP UX have Virtual Network Adapter Concept if ,it has where I can Find if I Install Virutal Network Adapter or which command that i can get it or which software can generate thanks (2 Replies)
Discussion started by: alert0919
2 Replies

8. Linux

Howto Detect New Nic Card

Hi PPL! I have P-IV processor, with on-board NIC card. I have added one more NIC card for domestic use. My kudzu does not recognise the newly added PCMCIA NIC card. How to go about this one? Suggest PEnguin (0 Replies)
Discussion started by: chakri.penguin
0 Replies

9. HP-UX

configuring nic card

using sam i have tryed to configure the nic, however when i try to do so i get an error saying i couldn't as i was using BIND ? (0 Replies)
Discussion started by: bobstar01
0 Replies

10. UNIX for Advanced & Expert Users

No NIC Card?

Hello Everyone, While trying to configure my network interface card on my system which runs mandrake 7, I have faced many problems. I used commands like netconf, drakconf, ifconfig etc to configure my NIC but of no use. There is no output for dmesg|grep eth. Does that mean that mandrake... (2 Replies)
Discussion started by: cyno
2 Replies
Login or Register to Ask a Question