Hi all,
is it okay for US-III+ running at 1200 MHZ to excced 75° C on sun fire 880
here's the output when i ran
Code:
prtdiag -v
on sunfire 880 running solaris10
Code:
bash-3.00# prtdiag -v
System Configuration: Sun Microsystems sun4u Sun Fire 880
System clock frequency: 150 MHz
Memory size: 8192 Megabytes
========================= CPUs ===============================================
Run E$ CPU CPU
Brd CPU MHz MB Impl. Mask
--- ----- ---- ---- ------- ----
A 0 1200 8.0 US-III+ 11.1
B 1 1200 8.0 US-III+ 11.1
A 2 1200 8.0 US-III+ 11.1
B 3 1200 8.0 US-III+ 11.1
========================= Memory Configuration ===============================
Logical Logical Logical
MC Bank Bank Bank DIMM Interleave Interleaved
Brd ID num size Status Size Factor with
---- --- ---- ------ ----------- ------ ---------- -----------
A 0 0 512MB no_status 256MB 8-way 0
A 0 1 512MB no_status 256MB 8-way 0
A 0 2 512MB no_status 256MB 8-way 0
A 0 3 512MB no_status 256MB 8-way 0
B 1 0 512MB no_status 256MB 8-way 1
B 1 1 512MB no_status 256MB 8-way 1
B 1 2 512MB no_status 256MB 8-way 1
B 1 3 512MB no_status 256MB 8-way 1
A 2 0 512MB no_status 256MB 8-way 0
A 2 1 512MB no_status 256MB 8-way 0
A 2 2 512MB no_status 256MB 8-way 0
A 2 3 512MB no_status 256MB 8-way 0
B 3 0 512MB no_status 256MB 8-way 1
B 3 1 512MB no_status 256MB 8-way 1
B 3 2 512MB no_status 256MB 8-way 1
B 3 3 512MB no_status 256MB 8-way 1
========================= IO Cards =========================
Bus Max
IO Port Bus Freq Bus Dev,
Brd Type ID Side Slot MHz Freq Func State Name Model
---- ---- ---- ---- ---- ---- ---- ---- ----- -------------------------------- ----------------------
I/O PCI 8 B 0 33 33 5,0 ok SUNW,XVR-100 SUNW,375-3181
No failures found in System
===========================
========================= Environmental Status =========================
System Temperatures (Celsius):
-------------------------------
Device Temperature Status
---------------------------------------
CPU0 76 OK
CPU1 73 OK
CPU2 75 OK
CPU3 71 OK
MB 47 OK
IOB 44 OK
DBP0 45 OK
=================================
Front Status Panel:
-------------------
Keyswitch position: NORMAL
System LED Status:
GEN FAULT REMOVE
[OFF] [OFF]
DISK FAULT POWER FAULT
[OFF] [OFF]
LEFT THERMAL FAULT RIGHT THERMAL FAULT
[OFF] [OFF]
LEFT DOOR RIGHT DOOR
[OFF] [OFF]
=================================
Disk Status:
Presence Fault LED Remove LED
DISK 0: [PRESENT] [OFF] [OFF]
DISK 1: [PRESENT] [OFF] [OFF]
DISK 2: [PRESENT] [OFF] [OFF]
DISK 3: [PRESENT] [OFF] [OFF]
DISK 4: [PRESENT] [OFF] [OFF]
DISK 5: [PRESENT] [OFF] [OFF]
DISK 6: [ EMPTY]
DISK 7: [ EMPTY]
DISK 8: [ EMPTY]
DISK 9: [ EMPTY]
DISK 10: [ EMPTY]
DISK 11: [ EMPTY]
=================================
Fan Bank :
----------
Bank Speed Status Fan State
( RPMS )
---- -------- --------- ---------
CPU0_PRIM_FAN 3191 [ENABLED] OK
CPU1_PRIM_FAN 3333 [ENABLED] OK
CPU0_SEC_FAN 0 [DISABLED] OK
CPU1_SEC_FAN 0 [DISABLED] OK
IO0_PRIM_FAN 4054 [ENABLED] OK
IO1_PRIM_FAN 3846 [ENABLED] OK
IO0_SEC_FAN 0 [DISABLED] OK
IO1_SEC_FAN 0 [DISABLED] OK
IO_BRIDGE_PRIM_FAN 3703 [ENABLED] OK
IO_BRIDGE_SEC_FAN 0 [DISABLED] OK
=================================
Power Supplies:
---------------
Current Drain:
Supply Status Fan Fail Temp Fail CS Fail 3.3V 5V 12V 48V
------ ------------ -------- --------- ------- ---- -- --- ---
PS0 GOOD 6 3 2 3
PS1 GOOD 5 3 2 3
PS2 GOOD 6 3 2 3
========================= HW Revisions =======================================
System PROM revisions:
----------------------
OBP 4.13.0 2004/01/19 18:26
IO ASIC revisions:
------------------
Port
Model ID Status Version
-------- ---- ------ -------
Schizo 8 ok 7
Schizo 9 ok 7
If the default high temperature warning threshold is 95 and shutdown is 100. I had a look at a couple of boxes to compare and I have a range of 73 - 78 on machines that are doing a moderate amount of work.
I am planning to install slack 13.37 on an old stand-alone PIII (512 mb ram) with 17 gb disk space. I need to keep lotsa pdf, chm type e-books for programming with few other misc. documents.
I'm going to use this system for my personal use.
It has no network but I browse internet with cable... (0 Replies)
Hi,
I'm newbee to AIX and would like to setup a process which kills 1 Hr. ideal users from smit. Please advise for making it work. :)
Thanks,
Sumit (2 Replies)
i want to set limits in /etc/security/limits.conf.My os is rhel 5.2.
It was giving continuous messages in in /var/log/secure like :
continuously.
I have changed values of priority and nice to "0" from unlimited and messages are not comming. But i want to know what is the ideal/maximum... (3 Replies)
Hi,
we have a solaris setup in our company and i have been assigned on a project of planning a backup strategy . ours is a midium level company.
please help me so that i can plan an Ideal Backup Strategy.
Thanks,
Una (6 Replies)
