setting a route in Solaris


 
Thread Tools Search this Thread
Operating Systems Solaris setting a route in Solaris
# 1  
Old 08-29-2003
setting a route in Solaris

I am having problems getting this to work, though it seems like it would be simple. I have a host with 2 interfaces, hme0 (192.168.0.132) for the primary interface, and hme1 (192.168.0.16) for backups. I want it to talk to the backup host, which is 192.168.0.21, across the hme1 interface.

Thanks
# 2  
Old 09-02-2003
Normally I've seen it put on a different subnet (so as to insure it goes across the correct interface/subnet) but setting a host route may help:

/usr/sbin/route add -host 192.168.0.21 192.168.0.16 1
# 3  
Old 09-16-2003
Help with NIC SETUP

I've been looking at how to install my D-Link NIC and I just can't make it work. I checked the DLINK Homepage but it wasn't very helpful, could someone please tell me how to configure my NIC on my Solaris x86 box, I got a DFE 530TX+
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. Solaris

Couldn't add route on Solaris 10

Hi Solaris Experts, I am trying to add a routing table entry on our 5.1 Generic_144488-12 sun4v sparc Solaris 10 SUNW,SPARC-Enterprise-T5220 so that it is possible to ping 10.56.9.34 node # netstat -rnv IRE Table: IPv4 Destination Mask Gateway Device Mxfrg Rtt Ref Flg Out In/Fwd ... (2 Replies)
Discussion started by: gjackson123
2 Replies

2. Solaris

Add route to solaris 10

I need to add a new route on solaris10 machine. I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway. How I do ? Thank you in advance. (1 Reply)
Discussion started by: arfry
1 Replies

3. Solaris

route and interface configuration in solaris

Hi, Every time when i boot my system i have to manually issue the following commands. ifconfig elxl0 plumb 192.168.200.129 netmask 255.255.255.0 up route add default 192.168.200.1 I need some help so that it should be configured permanently and i wouldn't have to manually issue... (2 Replies)
Discussion started by: malikshahid85
2 Replies

4. Solaris

Route new network interface Solaris 8

Hi there, I'm trying to configure an additional network interface on Solaris 8 (eri0). The interface has been activated, but all the frames are still routed to the current default interface (ce0) I've tried following command (with various syntaxes...) unsuccessfully so far: # route add... (2 Replies)
Discussion started by: sreiniche
2 Replies

5. Solaris

solaris 10 u5 what happens if no default route configured

Hi, I am new to solaris 10. What is the procedure the os takes if a default route is not configured? I am using a multihomed server with 4 interfaces. It looked strange to me this morning, because i had not defined a default route it defaulted to making one up, with the ip address of another... (9 Replies)
Discussion started by: borderblaster
9 Replies

6. Solaris

Solaris Route configuraion

Hi, Any one can help me in this below mentioned issue I am facing in my solaris server? here the scenario goes.... i have multiple segments in my LAN like remote csr, database, production etc. and all the segments are configured in Windows/CISCo network. from my all system in remote... (1 Reply)
Discussion started by: Praan
1 Replies

7. Solaris

Setting up route on subnet

I was told this worked on an HP system (same network as the sun server I am trying to set this up on)> but I get "netmask: bad value"2when I try it on the Sun: route add net 199.42.23.192 netmask 255.255.255.192 204.104.63.30 1 I've tried many different iterations (leaving out netmask, only... (2 Replies)
Discussion started by: nhmeanie
2 Replies

8. Solaris

SOLARIS does not route

hi, i installed solaris 9 on an SPARC server with two network interfaces. behind each interface is a small lan. i can reach every computer in every lan using one of the other interface when i am logged in the solaris. but if a computer from one lan has to connect to a computer on the other lan,... (4 Replies)
Discussion started by: bong02
4 Replies

9. IP Networking

add route to a subnet - Solaris 2.6

WE are running Unix - Solaris 2.6, we create a subnet. In the windows enviroment we are able to add a static route by using route add -p 172.16.10.0 mask 255.255.255.0 172.16.17.224, but when we add the route in Solaris as route add -net 172.16.10.0 255.255.255.0 172.16.17.224, we receive an... (5 Replies)
Discussion started by: cassy
5 Replies

10. UNIX for Advanced & Expert Users

Route for Solaris 8

Hello Dear Friends, I'm here again I need to know where is the permanent file for gateway configuration. I did the following command route add -net 0.0.0.0 5.0.0.3 ( My Gateway), but when i restart my computer i have to do it again. What the file can i set the permanent configuration for my... (1 Reply)
Discussion started by: themask
1 Replies
Login or Register to Ask a Question