10 More Discussions You Might Find Interesting
1. AIX
VIO Server connected to switch port and running with half duplex speed on one of the shared ethernet adapter. We have verified at switch end and everythings looks good.
Other ethernet adapter in the VIO server are connected and running in Full duplex speed.
Please help me find why this shared... (4 Replies)
Discussion started by: mugunthanvh
4 Replies
2. AIX
How to change Speed Duplex !
How to change Speed Duplex by command
chdev -P -l ent1 -a media_speed=1000_Full_Duplex
How to change Speed Duplex by Smitty .
smitty chgenet -> select adapter -> change Media speed etc. -> set "Apply change to DATABASE only" to yes -> Enter -> ... (0 Replies)
Discussion started by: ITHelper
0 Replies
3. Solaris
Hi,
How to find whether the server is running with half duplex or full duplex. I tried with the following command ndd -get /dev/ but am not getting any output,. Is the command correct?
Also let me know how to change from half to full duplex. (1 Reply)
Discussion started by: rogerben
1 Replies
4. UNIX for Advanced & Expert Users
Hi,
Someone told me how to check the remote switch port's speed setting on the other end of the cable, from linux. I forgot it.
Anyone knows? I checked dmesg, ethtool (haven't checked this out thoroughly) , no luck.
thanks,
Marc (1 Reply)
Discussion started by: marcpascual
1 Replies
5. Filesystems, Disks and Memory
I analysed disk performance with blktrace and get some data:
read:
8,3 4 2141 2.882115217 3342 Q R 195732187 + 32
8,3 4 2142 2.882116411 3342 G R 195732187 + 32
8,3 4 2144 2.882117647 3342 I R 195732187 + 32
8,3 4 2145 ... (1 Reply)
Discussion started by: W.C.C
1 Replies
6. Solaris
Evening,
I am attempting to change the speed and duplex settings on a single interface on a bge card on an m3000 SPARC server. Currently the settings are as follows:
bge0 link: up speed: 1000 Mbps duplex: full
bge1 link: up speed: 100 Mbps ... (13 Replies)
Discussion started by: brialt1
13 Replies
7. Infrastructure Monitoring
Hi,
In UNIX, it's very easy to find the duplex speed. But in Windows, is there a easy way to find the duplex speed? I can't go to over 100 servers to find this out, I was wondering if I run one command to do this?
Please advice. (2 Replies)
Discussion started by: samnyc
2 Replies
8. IP Networking
As a rule of thumb in doing calculations, what figure would you use in Mbytes/sec? I know the answer varies grealty on the topolgy of the network but I wonde what newteok engineers use a rough rule of thumb?
Many thanks. (1 Reply)
Discussion started by: debd
1 Replies
9. IP Networking
I have a TOSHIBA AS7000 B150 Sun Box
I wanted to run it with 100M/full duplex
I had added this to the /etc/system file to make to setting permenant So it would be set correctly on reboot.
set eri:eri_adv_100fdx_cap=1
set eri:eri_adv_100hdx_cap=0
set eri:eri_adv_autoneg_cap=0
But when I... (4 Replies)
Discussion started by: AirWalker83
4 Replies
10. Solaris
How can I tell on Solaris 9 sparc if my nics are running 100 gigabit full duplex... (4 Replies)
Discussion started by: csaunders
4 Replies