Login or Register to Ask a Question and Join Our Community


Solaris

how to force e1000g0 interface in solaris 10

Login to Discuss or Reply to this Discussion in Our Community

 
Thread Tools Search this Thread
Operating Systems Solaris how to force e1000g0 interface in solaris 10
# 1  
Old 04-03-2009
how to force e1000g0 interface in solaris 10
Hi all,

I encounter some problem with my e1000g interface running on sol 10. I can't permanently change the auto-nego to disable, if i use ndd commands, it will only stay until the next reboot.

But i can't change the link speed either is set to /etc/init.d/nddconfig or using ndd commands.

Anyone have any solution for this please help.

Million thanks.
# 2  
Old 04-03-2009
do the needed changes in "/kernel/drv/e1000g.conf". read the needed information in "man e1000g".
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. Solaris

How to increase the e1000g0 interface speed in Solaris?

Hi All, Please let me know the step by step process to set the e1000g0 interface speed to 1000mbps with full duplex from 100fdx and how to disable the auto negotiation with switch?. Thanks and Regards, Ganesh. (7 Replies)
Discussion started by: gsrungav
7 Replies

2. Solaris

Interface e1000g0 not showing in running state

Hello all, I have a sun server SunOS PNR1RAD01 5.10 Generic_144488-09 sun4v sparc SUNW,Netra-T5220 where i have an interface e100g0. This was earlier in running state but now this doesnt show running state. I tried to reset the interface, checked the cable but it did not help. Can nyone pls... (10 Replies)
Discussion started by: rajjat2
10 Replies

3. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies

4. Solaris

How to force a same password in Solaris in Solaris 8?

hi all I need to add a user "abcd" and set the password same as the user id. But Solaris 8 is not allowing me to do it, is there any way we can force the password to be same as the user id. Any help would be appreciated. Thanks bash-3.00# cat /etc/release ... (9 Replies)
Discussion started by: imran721
9 Replies

5. Shell Programming and Scripting

how to grep only IP address of e1000g0 using ifconfig -a

Hello All, Can someone show me how to cat "only the IP address of e1000g0" using ifconfig -a. i am trying to grep only the ip address (xx.xx.xx.xx) from the bunch of all other things like, broadcast address, IPV4, UP........and so on. thanks (1 Reply)
Discussion started by: solaix14
1 Replies

6. Solaris

force umount in solaris 2.6

Hi All, Can someone share with me how to force umount in solaris 2.6? Thanks Leong (3 Replies)
Discussion started by: bkleong
3 Replies

7. Solaris

How to force the LAN interface running on 10M

Hi all, I would like to force the LAN card to use 10MB instead of 100MB in UNIX enviroment, please help. thanks! :) (3 Replies)
Discussion started by: Felixkoo
3 Replies

8. UNIX for Advanced & Expert Users

Double question: Apache mod_proxy and force connection over specific interface

Double question here ... Running on Debian Etch and Apache 2.0 1) Using mod_proxy and/or mod_proxy_http in apache 2.0. The basics of using mod_proxy are pretty simple so long as you're using a static config. I'm trying to figure out how to do it dynamically - that is, allow the entry of a... (4 Replies)
Discussion started by: Halfwalker
4 Replies

9. Cybersecurity

How to force NIC full 100 dpx in Solaris 8

Does any body knows how to force NIC to 100 Full Duplex in Solaris 8, should survive after reboot or shutdown. (2 Replies)
Discussion started by: s_aamir
2 Replies

10. UNIX for Advanced & Expert Users

How to force NIC full 100 dpx in Solaris 8

Does any body knows how to force NIC to 100 Full Duplex in Solaris 8, should survive after reboot or shutdown. (1 Reply)
Discussion started by: s_aamir
1 Replies
Login or Register to Ask a Question