Reg. NIC card


 
Thread Tools Search this Thread
Operating Systems Solaris Reg. NIC card
# 1  
Old 02-25-2009
Java Reg. NIC card

Hi friends i have problem with my home pc, i installed solaris 10 but my lan drivers are not installed, if i want to install drivers manually from where to download and how to install. I have Realtech lan card. when i type ifconfig -a it shows only localhost 127.0.0.0 Lo0 cannot see other than this. please Assist me.
# 2  
Old 02-25-2009
Did you try configuring the interface manually?

Can you see the network ?

execute
Quote:
#dladm show-dev
Or

Quote:
#prtconf |grep network
# 3  
Old 02-26-2009
This is the message i got

bash-3.00# dladm show-dev
vmxnet0 link: unknown speed: 0 Mbps duplex: unknown
bash-3.00# prtconf | grep network
bash-3.00#
# 4  
Old 02-26-2009
Try installing vmwaretools and ensure that you have dhcp turned on.
# 5  
Old 02-26-2009
Java

There is no changes after i install vmware tools, actually i want to install the drivers in my pc not in vmware, i search in google to download drivers for REALTECH still cannot fine.
# 6  
Old 02-26-2009
Quote:
Originally Posted by kurva
want to install the drivers in my pc not in vmware
In that case, try googling "realtek nic drivers <your PC's OS>", and you shall find many useful docs.
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. Red Hat

Finding speed of NIC Card

Hi, I would like to know how to find out ACTUAL speed of NIC Card. I have used the command ethtool eth0, it is showing supported modes, but what is acutal speed ? how to find out? (4 Replies)
Discussion started by: manoj.solaris
4 Replies

2. HP-UX

NIC card issue

Hi, Someone asked me the below. If the box has multiple NIC cards, try to run a test with interface address specified as shown below $ java utils.MulticastTest -N server100 -A 237.155.155.1 -i <interfaceaddress> How can I now find out if my box has multiple NIC cards and how can I... (5 Replies)
Discussion started by: mohtashims
5 Replies

3. Linux

How to check which NIC Card is used for backups?

I have a linux box with 2 nic cards on it one for prod and one for backup. My question is while the backup are happening how do I determine which nic is used for backups . I would like to run a command so that that I can see the usage in a dynamic fashion. (7 Replies)
Discussion started by: new2prog
7 Replies

4. Linux

changing speed of NIC Card in linux

Hi, I would like to know how to change the speed of ethernet card in linux? as it is showing auto-neg using mii-tool -v eth0 and my requirement is 100mbps full duplex. Regards, Manoj (3 Replies)
Discussion started by: manoj.solaris
3 Replies

5. Solaris

NIC card repetative Failover

I have configure 2 NIC in ipmp group1 .Similarly other 2 NIC in ipmp group2 When I connect both NIC to 2 different switch , which is connect to one L3 switch as trunk. Both the NIC failover to each other continously. Following are the message log. ifmsdb1 in.mpathd: NIC failure detected... (0 Replies)
Discussion started by: abhaymittal003
0 Replies

6. Solaris

Reg- eth0,eth1 (ethernet card)

Hi Guys, I am working as a L-1 support and i want to know that are the precaution need to take on eth0(Ethernet card) i heard on production server it is very much important, what are the steps need to observe on this tickets. (1 Reply)
Discussion started by: kurva
1 Replies

7. HP-UX

how can I determine which NIC card is virtual NIC Card

how can I determine which NIC card is virtual NIC Card which condition can make a decision Does HP UX have Virtual Network Adapter Concept if ,it has where I can Find if I Install Virutal Network Adapter or which command that i can get it or which software can generate thanks (2 Replies)
Discussion started by: alert0919
2 Replies

8. Linux

Howto Detect New Nic Card

Hi PPL! I have P-IV processor, with on-board NIC card. I have added one more NIC card for domestic use. My kudzu does not recognise the newly added PCMCIA NIC card. How to go about this one? Suggest PEnguin (0 Replies)
Discussion started by: chakri.penguin
0 Replies

9. HP-UX

configuring nic card

using sam i have tryed to configure the nic, however when i try to do so i get an error saying i couldn't as i was using BIND ? (0 Replies)
Discussion started by: bobstar01
0 Replies

10. UNIX for Advanced & Expert Users

No NIC Card?

Hello Everyone, While trying to configure my network interface card on my system which runs mandrake 7, I have faced many problems. I used commands like netconf, drakconf, ifconfig etc to configure my NIC but of no use. There is no output for dmesg|grep eth. Does that mean that mandrake... (2 Replies)
Discussion started by: cyno
2 Replies
Login or Register to Ask a Question