hotlink - Network Interface Monitoring

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

2. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a...

3. IP Networking

network interface -

Hello, Please, how can i create a network interface with a routable IP address on linux (ubuntu) ? AND How can i desactivate an interface? Thank you so much for help.

4. IP Networking

Network interface-

Hello, Please what's the difference between: AND Thank you so much

5. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that.

6. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks

7. Solaris

Network interface configuration

Dears, i follow this to configure Network interface for my PC O/S : Unix Sun Solaris vi /etc/hostname.bge0 and write my ip vi /etc/netmasks and write my subnetmask vi /etc/defautrouter and write my gatwey vi /etc/resolv.conf and write my DNS after i reboot My Computer ...

8. IP Networking

How to activate a network interface?

What are the steps between "ifconfig eth0 UP" and "net_device->open"? ifconfig eth0 UP => ioctl(skfd, SIOCSIFFLAGS, &ifr) (ifr.ifr_flags = IFF_UP | IFF_RUNNING) => ????? => what are these steps? net_device->open Thanks!

9. UNIX for Advanced & Expert Users

network interface problem

Hi expert, Need some help on network interface issue.. I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0...

10. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt

LEARN ABOUT NETBSD

txp

TXP(4)							   BSD Kernel Interfaces Manual 						    TXP(4)

NAME

     txp -- 3Com 3XP Typhoon/Sidewinder (3CR990) Ethernet interface

SYNOPSIS

     txp* at pci? dev ? function ?

DESCRIPTION

     The txp interface provides access to the 10Mb/s and 100Mb/s Ethernet networks via the 3Com Typhoon/Sidewinder chipset.  This driver supports
     the following cards:

	   o   3Com 3CR990-TX-95
	   o   3Com 3CR990-TX-97
	   o   3Com 3CR990SVR95
	   o   3Com 3CR990SVR97

     Basic Ethernet functions are provided as well as support for vlan(4) tag removal and insertion assistance, receive ip(4), tcp(4), and udp(4)
     checksum offloading, and transmit ip(4) checksum offloading.  There is currently no support for transmit tcp(4) or udp(4) checksum offload-
     ing, tcp(4) segmentation, nor ipsec(4) acceleration.  Note that hardware checksumming is only used when the interface is not in bridge(4)
     mode.

     Each of the host's network addresses is specified at boot time with an SIOCSIFADDR ioctl(2).  The txp interface employs the address resolu-
     tion protocol described in arp(4) to dynamically map between Internet and Ethernet addresses on the local network.

     When a txp interface is brought up, by default, it will attempt to auto-negotiate the link speed and duplex mode.	The speeds, in order of
     attempt, are: 100Mb/s Full Duplex, 100Mb/s Half Duplex, 10 Mb/s Full Duplex, and 10 Mb/s Half Duplex.

     The txp supports several media types, which are selected via the ifconfig(8) command.  The supported media types are:

	   media autoselect
			   Attempt to autoselect the media type (default)

	   media 100baseTX mediaopt full-duplex
			   Use 100baseTX, full duplex

	   media 100baseTX [mediaopt half-duplex]
			   Use 100baseTX, half duplex

	   media 10baseT mediaopt full-duplex
			   Use 10baseT, full duplex

	   media 10baseT [mediaopt half-duplex]
			   Use 10baseT, half duplex

SEE ALSO

     arp(4), ifmedia(4), inet(4), intro(4), ip(4), netintro(4), pci(4), tcp(4), udp(4), vlan(4), ifconfig(8)

HISTORY

     The txp driver first appeared in NetBSD 2.0.

BSD
								  August 21, 2003							       BSD

Solaris BigAdmin RSS