hotlink - Network Interface Monitoring

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

2. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a...

3. IP Networking

network interface -

Hello, Please, how can i create a network interface with a routable IP address on linux (ubuntu) ? AND How can i desactivate an interface? Thank you so much for help.

4. IP Networking

Network interface-

Hello, Please what's the difference between: AND Thank you so much

5. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that.

6. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks

7. Solaris

Network interface configuration

Dears, i follow this to configure Network interface for my PC O/S : Unix Sun Solaris vi /etc/hostname.bge0 and write my ip vi /etc/netmasks and write my subnetmask vi /etc/defautrouter and write my gatwey vi /etc/resolv.conf and write my DNS after i reboot My Computer ...

8. IP Networking

How to activate a network interface?

What are the steps between "ifconfig eth0 UP" and "net_device->open"? ifconfig eth0 UP => ioctl(skfd, SIOCSIFFLAGS, &ifr) (ifr.ifr_flags = IFF_UP | IFF_RUNNING) => ????? => what are these steps? net_device->open Thanks!

9. UNIX for Advanced & Expert Users

network interface problem

Hi expert, Need some help on network interface issue.. I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0...

10. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt

LEARN ABOUT X11R4

systemd-networkd

SYSTEMD-NETWORKD.SERVICE(8)				     systemd-networkd.service				       SYSTEMD-NETWORKD.SERVICE(8)

NAME

       systemd-networkd.service, systemd-networkd - Network manager

SYNOPSIS

       systemd-networkd.service

       /lib/systemd/systemd-networkd

DESCRIPTION

       systemd-networkd is a system service that manages networks. It detects and configures network devices as they appear, as well as creating
       virtual network devices.

       To configure low-level link settings independently of networks, see systemd.link(5).

       systemd-networkd will create network devices based on the configuration in systemd.netdev(5) files, respecting the [Match] sections in
       those files.

       systemd-networkd will manage network addresses and routes for any link for which it finds a .network file with an appropriate [Match]
       section, see systemd.network(5). For those links, it will flush existing network addresses and routes when bringing up the device. Any
       links not matched by one of the .network files will be ignored. It is also possible to explicitly tell systemd-networkd to ignore a link by
       using Unmanaged=yes option, see systemd.network(5).

       When systemd-networkd exits, it generally leaves existing network devices and configuration intact. This makes it possible to transition
       from the initrams and to restart the service without breaking connectivity. This also means that when configuration is updated and
       systemd-networkd is restarted, netdev interfaces for which configuration was removed will not be dropped, and may need to be cleaned up
       manually.

CONFIGURATION FILES

       The configuration files are read from the files located in the system network directory /lib/systemd/network, the volatile runtime network
       directory /run/systemd/network and the local administration network directory /etc/systemd/network.

       Networks are configured in .network files, see systemd.network(5), and virtual network devices are configured in .netdev files, see
       systemd.netdev(5).

SEE ALSO

       systemd(1), systemd.link(5), systemd.network(5), systemd.netdev(5), systemd-networkd-wait-online.service(8)

systemd 237													       SYSTEMD-NETWORKD.SERVICE(8)

Solaris BigAdmin RSS