10 More Discussions You Might Find Interesting
1. IP Networking
Hi @all,
I try to connect 2 LANs with IPSec/Openswan
LAN 1: 192.168.0.0/24
LAN 2: 192.168.1.0/24
This is my Config:
conn HomeVPN # # Left security gateway, subnet behind it, nexthop toward right. left=192.168.1.29 ... (1 Reply)
Discussion started by: bahnhasser83
1 Replies
2. UNIX for Dummies Questions & Answers
Hi,
I'm a beginner and am learning c programming. I want to learn UNIX/LINUX in parallel. But I don't know difference between UNIX and LINUX and where they are applied in real life. As a beginner, some people asked me to start with UNIX. Please let me know some very good books for UNIX. Also a... (6 Replies)
Discussion started by: nerdbee
6 Replies
3. IP Networking
Q: "Does Cisco 1921 router support,, act as an endpoint for, site to site VPNs using IPSec? If so, how many? "
A: If you get the Cisco 1921/k9 with the security services bundle then it will have built in security features. Cisco, typically includes IP Sec tunnels I believe as part of that... (0 Replies)
Discussion started by: Ayaerlee
0 Replies
4. IP Networking
Hi,
I am trying to establish vpn between my linux server and cisco asa at client side.
I installed openswan on my cent os.
Linux Server
eth0 - 182.2.29.10
Gateway - 182.2.29.1
eth1 - 192.9.200.75
I have simple IPtables Like
WAN="eth0"
LAN="eth1" (0 Replies)
Discussion started by: ashokvpp
0 Replies
5. Shell Programming and Scripting
i am jaswanth,
i am very new to unix/linux, upto now i worked in windows only., but i took coatching for unix.., and my sir teached all my classes in red hat linux and told me that all are same...!!!
I know shall programming in red hat linux..,
but now i installed opensloaris but the... (5 Replies)
Discussion started by: strgraphics
5 Replies
6. IP Networking
Setup a site to site VPN between two cisco routers.
One of the site locations is unable to access ports such as https://example.com:9001
How do I let them go into port 9001?
They can ssh, ftp, telnet and everything else.
Is this a VPN issue or ACL access issue?
I put
permit ip host... (0 Replies)
Discussion started by: photon
0 Replies
7. Shell Programming and Scripting
Hi!
I need to install a application from one server to several other servers. My script would copy the install-script to other machines and run it.Since it has to be non-interactive , just wondering if yum can be used for the same.
Please let me know , if you guys are aware of other... (1 Reply)
Discussion started by: nua7
1 Replies
8. Shell Programming and Scripting
Hi All,
I have made the following code which is taking 10-15 mins to execute completely. Here the file am using is very big( around 1050993843). Can any one make some changes in my code which reduces the time it takes to execute as am very much new to Unix(learner).
One more thing, i have... (10 Replies)
Discussion started by: madhavsunduru
10 Replies
9. Shell Programming and Scripting
Hi
I have the following at the end of a service shutdown script used in part of an active-passive failover setup:
###
# Shutdown all primary Network Interfaces
# associated with failover
###
# get interface names based on IP's
# and shut them down to simulate loss of
# heartbeatd
... (1 Reply)
Discussion started by: mikie
1 Replies
10. AIX
Hi,
I am new script programming, I have written a script shown velow to read username and passwd from /etc/security/passwd, i am able to read username, but unable to grep lastupdate. please look into the code and suggest if any changes need.
#!/bin/ksh
USERNAME=""
fname=/usr/bin/lastupdate... (1 Reply)
Discussion started by: me_haroon
1 Replies