10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
Hi
I am trying to create a script extracting the IP provided by ifconfig.
I tried with grep + awk but I am returned more than I need.
/sbin/ifconfig eth0 | grep "inet addr:" | awk '/inet addr:/ { print $2 }'
and returns
addr:10.15.1.64
How can I remove "addr:" string?... (9 Replies)
Discussion started by: manustone
9 Replies
2. Solaris
Hi all,
I encounter some problem with my e1000g interface running on sol 10. I can't permanently change the auto-nego to disable, if i use ndd commands, it will only stay until the next reboot.
But i can't change the link speed either is set to /etc/init.d/nddconfig or using ndd commands.
... (1 Reply)
Discussion started by: mailbox80
1 Replies
3. Solaris
hi,
I am trying to configure one of my interfaces, but after reboot - i lose the changes to the netmask & broadcast address.
I have added an entry in /etc/netmasks, but it doesnt pick up the new settings. any ideas - much appreciated.
before reboot:
eri0:... (3 Replies)
Discussion started by: badoshi
3 Replies
4. IP Networking
I'm working on an AIX Unix LPAR (AIX 3.5 00C3C9904C00 as returned by uname -a)
I can access this box using telnet, port 22 using adress IP A and B
A=AA.AA.XX.XX and B=AA.AA.YYY.YYY
I can confirm these 2 are the same space, I can see
I can't find address B listed anywhere... so I wonder what... (1 Reply)
Discussion started by: Isax50
1 Replies
5. Shell Programming and Scripting
I'm a newbie to linux, so pleases forgive me!
I would like to find a script that I could use to extract a dynamic ip from the ppp0 and set it as a variable to be used in IPTables
basically, if ppp0 ip address is 10.10.10.20, I would like a script that would set a var to 10.10.10.0. of... (9 Replies)
Discussion started by: speedy3k
9 Replies
6. Shell Programming and Scripting
hi,
i want to know how to grep inet address for below
below is the output of ifconfig command
/home/JA> ifconfig
eth0 Link encap:Ethernet HWaddr 00:11:0A:5B:2E:E9
inet addr:161.239.203.18 Bcast:161.239.203.127 Mask:255.255.255.128
UP BROADCAST RUNNING... (3 Replies)
Discussion started by: mail2sant
3 Replies
7. IP Networking
HI All,
My interface card has failed.If i am giving the command to uplumb it i am getting an error.
ce401001: flags=219040843<UP,BROADCAST,RUNNING,MULTICAST,DEPRECATED,IPv4,NOFAILOVER,FAILED,CoS> mtu 1500 index 3
inet 10.188.24.18 netmask ffffffc0 broadcast 10.188.24.63
# ifconfig... (2 Replies)
Discussion started by: sag71155
2 Replies
8. IP Networking
Hello,
I have a server with two ip addresses. I need to make the ip address that's currently the secondary the primary. How do I use the ifconfig command and primary option?
Thanks. (5 Replies)
Discussion started by: pmichner
5 Replies
9. UNIX for Dummies Questions & Answers
if i have the command ifconfig eth0, what will the output be and how can i use either awk or grep to isolate and display the IP address, subnet mask and physical address of my host (1 Reply)
Discussion started by: carlvernon
1 Replies
10. Solaris
hi all
iam trying to set my eri0 interface but with little luck .
when i set the ip using ipconfig i always get "bad adress"..
moreover when i use ifconfig eri0 i can notice that the inet is 0.0.0.0 and the netmask 0
i am runnig solaris 9 on sparc .
any helpis highly appreciated ... ... (2 Replies)
Discussion started by: ppass
2 Replies
