How to make awk command faster for large amount of data?


 
Thread Tools Search this Thread
Top Forums Shell Programming and Scripting How to make awk command faster for large amount of data?
# 22  
Old 10-09-2018
What I did was stop the overhead descompressing and stop reading the file when timestamp was higher than what I need.
Another thing I realized was that every file has only 3 consecutive hours, so I made a bash script to use this information to know the same thing that I was getting with tail, but without the overhead. This way I used only files that would possible have what I needed,

Thank you all for helping. The points explained to me here helped me to understand better how to indentify where was the bottleneck in my script.
This User Gave Thanks to brenoasrm For This Post:
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. Shell Programming and Scripting

How to make awk command faster?

I have the below command which is referring a large file and it is taking 3 hours to run. Can something be done to make this command faster. awk -F ',' '{OFS=","}{ if ($13 == "9999") print $1,$2,$3,$4,$5,$6,$7,$8,$9,$10,$11,$12 }' ${NLAP_TEMP}/hist1.out|sort -T ${NLAP_TEMP} |uniq>... (13 Replies)
Discussion started by: Peu Mukherjee
13 Replies

2. Shell Programming and Scripting

Perl : Large amount of data put into an array

This basic code works. I have a very long list, almost 10000 lines that I am building into the array. Each line has either 2 or 3 fields as shown in the code snippit. The array elements are static (for a few reasons that out of scope of this question) the list has to be "built in". It... (5 Replies)
Discussion started by: sumguy
5 Replies

3. Shell Programming and Scripting

awk changes to make it faster

I have script like below, who is picking number from one file and and searching in another file, and printing output. Bu is is very slow to be run on huge file.can we modify it with awk #! /bin/ksh while read line1 do echo "$line1" a=`echo $line1` if then echo "$num" cat file1|nawk... (6 Replies)
Discussion started by: mirwasim
6 Replies

4. Shell Programming and Scripting

Faster way to use this awk command

awk "/May 23, 2012 /,0" /var/tmp/datafile the above command pulls out information in the datafile. the information it pulls is from the date specified to the end of the file. now, how can i make this faster if the datafile is huge? even if it wasn't huge, i feel there's a better/faster way to... (8 Replies)
Discussion started by: SkySmart
8 Replies

5. Shell Programming and Scripting

Running rename command on large files and make it faster

Hi All, I have some 80,000 files in a directory which I need to rename. Below is the command which I am currently running and it seems, it is taking fore ever to run this command. This command seems too slow. Is there any way to speed up the command. I have have GNU Parallel installed on my... (6 Replies)
Discussion started by: shoaibjameel123
6 Replies

6. Emergency UNIX and Linux Support

Help to make awk script more efficient for large files

Hello, Error awk: Internal software error in the tostring function on TS1101?05044400?.0085498227?0?.0011041461?.0034752266?.00397045?0?0?0?0?0?0?11/02/10?09/23/10???10?no??0??no?sct_det3_10_20110516_143936.txt What it is It is a unix shell script that contains an awk program as well as... (4 Replies)
Discussion started by: script_op2a
4 Replies

7. Shell Programming and Scripting

How to tar large amount of files?

Hello I have the following files VOICE_hhhh SUBSCR_llll DEL_kkkk Consider that there are 1000 VOICE files+1000 SUBSCR files+1000DEL files When i try to tar these files using tar -cvf backup.tar VOICE* SUBSCR* DEL* i get the error: ksh: /usr/bin/tar: arg list too long How can i... (9 Replies)
Discussion started by: chriss_58
9 Replies

8. AIX

amount of memory allocated to large page

We just set up a system to use large pages. I want to know if there is a command to see how much of the memory is being used for large pages. For example if we have a system with 8GB of RAm assigned and it has been set to use 4GB for large pages is there a command to show that 4GB of the *GB is... (1 Reply)
Discussion started by: daveisme
1 Replies

9. Programming

Read/Write a fairly large amount of data to a file as fast as possible

Hi, I'm trying to figure out the best solution to the following problem, and I'm not yet that much experienced like you. :-) Basically I have to read a fairly large file, composed of "messages" , in order to display all of them through an user interface (made with QT). The messages that... (3 Replies)
Discussion started by: emitrax
3 Replies

10. Shell Programming and Scripting

awk help to make my work faster

hii everyone , i have a file in which i have line numbers.. file name is file1.txt aa bb cc "12" qw xx yy zz "23" we bb qw we "123249" jh here 12,23,123249. is the line number now according to this line numbers we have to print lines from other file named... (11 Replies)
Discussion started by: kumar_amit
11 Replies
Login or Register to Ask a Question
SHTOOL-PATH.TMP(1)					      GNU Portable Shell Tool						SHTOOL-PATH.TMP(1)

NAME
shtool-path - GNU shtool command dealing with shell path variables SYNOPSIS
shtool path [-s|--suppress] [-r|--reverse] [-d|--dirname] [-b|--basename] [-m|--magic] [-p|--path path] str [str ...] DESCRIPTION
This command deals with shell $PATH variables. It can find a program through one or more filenames given by one or more str arguments. It prints the absolute filesystem path to the program displayed on "stdout" plus an exit code of 0 if it was really found. OPTIONS
The following command line options are available. -s, --suppress Supress output. Useful to only test whether a program exists with the help of the return code. -r, --reverse Transform a forward path to a subdirectory into a reverse path. -d, --dirname Output the directory name of str. -b, --basename Output the base name of str. -m, --magic Enable advanced magic search for ""perl"" and ""cpp"". -p, --path path Search in path. Default is to search in $PATH. EXAMPLE
# shell script awk=`shtool path -p "${PATH}:." gawk nawk awk` perl=`shtool path -m perl` cpp=`shtool path -m cpp` revpath=`shtool path -r path/to/subdir` HISTORY
The GNU shtool path command was originally written by Ralf S. Engelschall <rse@engelschall.com> in 1998 for Apache. It was later taken over into GNU shtool. SEE ALSO
shtool(1), which(1). 18-Jul-2008 shtool 2.0.8 SHTOOL-PATH.TMP(1)