10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
Hello
I have a file which has around 120 lines of commands.
I am trying to write a shell script like which reads the 'command' file and executes line by line with some additional (common argument) with maximum 6 commands active at a time. Each of these commands when executed takes time... (5 Replies)
Discussion started by: JackyShane_36
5 Replies
2. Shell Programming and Scripting
Good Day Everyone,
I was hoping to get a little insight into an expect script that I've written.
Basically we have this expect script to perform an sftp upload, key authentication is not an option, and sftp is the only method supported by our vendor, thus the need for this.
I want to be... (3 Replies)
Discussion started by: thaller
3 Replies
3. Shell Programming and Scripting
Hi,
I need your guys help again. I run a script which check for some process status in a loop. when i check the process some of the process could throw an error, how can i check that inside my script.
Thanks,
RR (3 Replies)
Discussion started by: rrb2009
3 Replies
4. Shell Programming and Scripting
Hi All,
How can we handle file operation in scripts. I have written a script that run ok otherwise however the "Cat" operation leaves a process open on the box. Command is like
cat "${LASTFILENAME}" | /usr/xpg4/bin/awk -F, '{do{if ($3 == "100" && $4 == "300" && $170 ~ /^abc/) {
... (2 Replies)
Discussion started by: raman1605
2 Replies
5. UNIX for Dummies Questions & Answers
I'm trying to write a script that will handle the input from the ls command in my script so I can then manipulate the data.
For example, I want to capture the output of the ls command in my script and then do a differences between the filename received in to another directory.
ls |... (1 Reply)
Discussion started by: spookyrtd99
1 Replies
6. Shell Programming and Scripting
hi there,
i just need a help handling the output of filespec in case has been picked
im writing a bash script similar to the command ls,
and ive done everything except handing the filespec which i spent more than 3 hrs and i coundn't figure out or find any on the net.
all what i need is... (11 Replies)
Discussion started by: new2Linux
11 Replies
7. SCO
when I do a tape status /dev/rStp0 I get the following on a new tape and I have tried several:
Status : ready beginning-of-tape
soft errors : 0
hard errors: 2
underruns: 5
My BackupEdge has stopped backing up my system because it asks for a new volume yet my total system data is under 20... (5 Replies)
Discussion started by: psytropic
5 Replies
8. Shell Programming and Scripting
Hi
! /bin/sh
set logdir1 "logDir/local/logname"
#write the filename into a file
echo $logdir1 >> logname.txt
how do i exec the above echo command (1 Reply)
Discussion started by: nathgopi214
1 Replies
9. UNIX for Dummies Questions & Answers
I have a shell script, which calls a load script to load a database. How can i handle errors in Unix(similar to 'error level' in Batch scripts)? I am trying to use 'mailx' to send a Success/failure message based on the error level returned by the load script.
I have already used an error log... (2 Replies)
Discussion started by: sarsani
2 Replies
10. UNIX for Dummies Questions & Answers
hi guys,
I.m trying to remove and add a new tape drive by using the mkdev tape command and when i try to update the Kernel this is what i'm getting,
i386ld: Symbol Sdsk_no_tag in /var/opt/K/SCO/link/1.1.1Eb/etc/conf/pack.d/blad/s
pace.o is multiply defined. First defined in... (0 Replies)
Discussion started by: josramon
0 Replies