9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
I have a really old distro (FC7) that I am trying to make compatible with some new hardware (ie. new RAID drivers)...
I put the RAID driver into the ISO so that the installer can detect the RAID set... but post-install (aka: first boot) it appears that the Anaconda-generated initrd does not have... (0 Replies)
Discussion started by: jjinno
In general terms what are the differences platform driver,codec driver and Machine driver? (1 Reply)
Discussion started by: rupeshkp728
3. UNIX for Dummies Questions & Answers
Help, suspect hacked via serial or electric! any ideas on error "Pid:1, comm:swapper Tainted:G W 2.6.35-22 generic #33 -unbutu device = "(null)" or unknown-blocklist(8.1) please append a correct "root"boot option Available partitions 0b00 1048575 sr0 driver:sr 0800 488386584 sda driver:sd. Thanks... (3 Replies)
Discussion started by: kryclear
I compiled TUN 1.1 driver on my Solaris 10 64bit, and everything was working fine, all the commands for installation were successfull (add_drv, devfsadm -i tun ... etc.)
and the driver was working fine as I got OpenVPN server up and running with successful clients attached. My only problem... (2 Replies)
Discussion started by: TomSu
I use the uptime command,but
it only show how long system has been up
up 18 days
but I want the this format
machine boot time YYYY-MM-DD hh:mm:ss
does any command can get that or how to i use program to do this (6 Replies)
Discussion started by: alert0919
When I get start program at boot
I read which run level
only read directory which directory name has UpperCase 'S'
is not enough
someone says that I need to reference another file
which file I need to reference
1)/etc/rc.config.d/all file which parameter... (4 Replies)
Discussion started by: alert0919
How do I get the number of tics or seconds since the last boot?
How do I convert tics to seconds?
Siegfried (3 Replies)
Discussion started by: siegfried
8. UNIX for Advanced & Expert Users
I have a program that check the IP address and automatic update it to the DNS server. I would like to run this program when the computer bootup after pppd get a connection. How do I add it to the init file. Does any one have any information of how to do it.
I run a Linux Mandrake as a... (1 Reply)
Discussion started by: vtran4270
9. UNIX for Dummies Questions & Answers
I'm looking for advice on where is the best place on Solaris to put a script that will setup system vairables prior to any users loging in. I've tried /etc/rc3.d without much success as the variables do not appear in the output from an env command.
I want the system to have these... (7 Replies)
Discussion started by: ianf
SBP_TARG(4) BSD Kernel Interfaces Manual SBP_TARG(4)
sbp_targ -- Serial Bus Protocol 2 (SBP-2) Target Mode devices driver
To compile this driver into the kernel, place the following lines in your kernel configuration file:
Alternatively, to load the driver as a module at boot time, place the following lines in loader.conf(5):
The sbp_targ driver provides support for SBP-2 target mode. This driver is supposed to work with cam(4), targ(4) and firewire(4). You also
need to use scsi_target(8), which can be found in /usr/share/examples/scsi_target, to provide actual devices.
# mdconfig -a -t malloc -s 10m
# scsi_target 0:0:0 /dev/md0
(Assuming sbp_targ0 on scbus0)
cam(4), firewire(4), targ(4), camcontrol(8), fwcontrol(8), kldload(8), scsi_target(8)
The sbp_targ driver was written by Hidetoshi Shimokawa.
This driver is currently under development. It does not work correctly in multi-initiator environments or after the bus topology has been
November 7, 2003 BSD