Search Results

Hi,

It was installed in /opt

Regards,
Rocky

Hi,

The agent is "Autosys". It was installed in a Sparse root zone with a separate mount point created for it.
Yes it is a third party agent.

Regards,
Rocky

Hi All,

I had installed an agent in one of the zones and it was working fine. After few days, we had patched that server and once the server came up and zone was up, The agent script and its files...

Hi Duke & Gull,

Thanks for your help and suggestions throughout.
The issue has been resolved and the server was patched successfully.
The issue was not with the drivers as i had updated the...

Hi Dave,

Generally what happens with this server is that we patch it using lu and once the server is not comming up, we login through the ALOM and enter into ok prompt and revert the server as we...

Hi All,

I have an server Sun Fire V245 for which we had been trying to patch.
We get a message that the patch has been applied successfully but while trying to reboot after activating the new...

Hi All,

We have a sparc server for which we always recieve memory utilization alerts. (97.01% available memory used by the partition (/MEMORY/MEMORY/MEMUsedMemPerc)).
But when we check the...

Hi Duke,

Thanks for your support regarding this. I had checked with media team and still there has been a confusion. Hence we have asked hardware vendor engineer's help to investigate and suggest...

Duke,

I had requested a check and media team person also says the same(bottom left) port is not blinking and that is the one which needs to be replaced.

But my doubt is that when i went...

Duke,

I was able to get the data from path_to_inst but could not understand this.

"/pci@0,0" 0 "npe"
"/pci@0,0/pci10de,5d@e" 3 "pcie_pci"
"/pci@0,0/pci10de,5d@e" 1 "pcieb"...

Hi Duke,

Below are the outputs of dladm show-dev and prtdiag -v

e1000g0 link: up speed: 1000 Mbps duplex: full
e1000g1 link: up speed: 1000 Mbps ...

Hi All,

I am having an Sun fire X4600 M2 server where one of the interfaces is down.
I had requested for the replacement but had a bit problem in identifying the port.
As per the server service...

Hi Sarfaraz,

My issue has been resolved.:)
The port was listening but it was disabled from firewall end with some rule.
Now it has been enabled and i am able to give test prints as well....

Hi Sarfaraz,

I had followed the steps exacty the way you suggested.
Once everyting is done, i get the status as ready and later once i give a test print, the status is down and the print is...

Hi Vbe,

This is the first server on this server as well as in AIX environment.
Earlier we had in solaris servers but there i had used hppi for configuring hp printers.

Any help would be...

Hi Sarfaraz,

Thanks for the post. This has helped me but i am unable to give test prints.
Can you please let me know how to give test prints and understand how it is working.
I had given test...

Hi All,

I have been trying to configure an HP laserjet printer on an AIX6.1 server through network as well as remote.
This is the first time i am configuring a printer on AIX.
I had been using...

Hi All,

I have been trying to perform alt disk installation for AIX 6.1 server.
Phas 3 fails and bosboot is not getting updated.
when i tried only phase 1 and phase 3 by skipping phase 2 for...

Hi Guys,

Thanks for your support.
I had got the solution from one of the posts and had it resolve my problem. I thought of sharing it here.

Step 1 --- Login to the physical server and...

Hi All,

I need to give an user sudo ability to root.
We have also generated RSA key but unable to proceed further.

For example after a user logs into the server normally and when he executes...

Hi All,

I need to mount an nfs filesystem as below.

xxx.xx.xx.xxx:/media/nss/Rocky Catherine/logs

For the above as there is space in between the name, hoping it will not mount, if i give...

Hi Murphy.

There was nothing changed. All of a sudden all printers stopped working.
Even tried to clear the queue but still were unable to print...

Hello Experts,

I have been facing an issue with printing through cups configured on Linux server.
All was going on well but all of a sudden the printers started giving an error message,...

solaris 5.10 Generic_147441-27 i86pc i386 i86pc

Hi,

When performing a patch on my solaris 10 server, i used LU as below.

Firstly created an LU boot environment.
Later when tried to patch the latest LU boot environment using...