10 More Discussions You Might Find Interesting
1. SCO
Hello all,
First off- great forum! I have learned a lot just by reading some of the questions and answers. Good to see there are good people out there still willing to help!
Here is my dilemma- I have a fairly new server running an Activant product on it, which runs SCO openserver 5.0.5... (9 Replies)
Discussion started by: crt001
9 Replies
2. UNIX for Advanced & Expert Users
Hi All ,
I wanted to install SCO Open server 5.0.7 on HP DC7600 Desktop Machine, is there any bootloader and which site i can find it to enable me install it because the system is not recognizing the Hard disk just like the ML G Series machine installations.
Please help if you have done this... (4 Replies)
Discussion started by: davosky
4 Replies
3. SCO
Hwey I manage a Unix box where I ama having multiple printer problems. the only way to get printers to print again is by rebooting. I stop and start services with no luck. Any one have any ideas? It can go weeks with being OK but then any given printer can go and cause the entire print queue to... (6 Replies)
Discussion started by: uk2us88
6 Replies
4. SCO
can not for the life of me workout which BTLD to load allways shows no HDD available can any one give me a clue
tried
hpsas
aacraid
lsil
a160
a320
server is a ML310 G4 ?????:confused::confused: (7 Replies)
Discussion started by: wildginger
7 Replies
5. SCO
we are installing Openserver 5.0.7, system have SAS controller (Hard Disk Attached) as well as Adaptec ultra 320 controller (Tape Drive Attached).
At the time of installation we link both driver BTLD
Boot: Defbootstr link=accraid ad320
Aftes succesfully installation of accraid btld... (6 Replies)
Discussion started by: hafizurr
6 Replies
6. SCO
Hi everyone,
We r installing sco openserver 5.07 on dell poweredge 2800 but we are facing problem when installing SCSI-raid drivers. Dell provide Perc4 raid card and we dont found raid drivers for this specific raid card. So we r stuck up on primary stage and we also dont know the... (2 Replies)
Discussion started by: mineshkoli
2 Replies
7. UNIX for Dummies Questions & Answers
Hello Guys.
This might be really easy for you guys but i'm really going crazy about this problem.
I have this user that is trying to login to my unix box and it will not let him pass the point where it says TERM = (ansi ) and the last line that shows is teminal is ansi. It wont go any further.... (7 Replies)
Discussion started by: josramon
7 Replies
8. SCO
I have installed the Ethereal package (ethereal-0.8.14.pkg) on a SCO Openserver 5.0.7. Installation went OK but when I try to start Ethereal I get error messages about "linking problems".
I have studied the SCO Technical article 116949 but my filenames differ from article.
Please help!! (1 Reply)
Discussion started by: bean2
1 Replies
9. UNIX for Dummies Questions & Answers
Hi guys,
Please bear with me
i have a sco 5.0.6 openserver i'm telnet in to it. (via dsl)
After 7 minutes it will kick me out of my program.
Is there any settings that i need to change in order to stop the time out problem.
I dont have any router or hub (dsl modem to nic card )
Also... (6 Replies)
Discussion started by: josramon
6 Replies
10. UNIX for Advanced & Expert Users
hi everybody
I have got a set of sco unix open server release 3.0 flopyy disks series N1, N2, M1, P1...P43, Release notes..
ý did a fresh installation. but ý cant install ethernet card. when ý use netconfig-ad a chain -tcpip... there is a messge :
the sco contain TCP/IP driver. and ý... (2 Replies)
Discussion started by: kaygusuz
2 Replies