PCI / PCIExpress Parallel port in SCO 6.0.0


 
Thread Tools Search this Thread
Operating Systems SCO PCI / PCIExpress Parallel port in SCO 6.0.0
# 1  
Old 04-17-2008
PCI / PCIExpress Parallel port in SCO 6.0.0

How do or what do I need to add PCI / PCIe (PCI Express) parallel ports add-on adapters to OpenServer 6.0.0? OpenServer 5 could see PCI slots but OpenServer 6.0.0 (Original CD or the Re-cut one) required a maintenance pack to be installed? Is this right and how do I check to see if these work?
# 2  
Old 04-17-2008
You should install the latest maintenance pack, and any other patches that are available.
Since the parallel port driver is no longer supported (see 'man parallel'), I would suggest that you acquire an ethernet/parallel adapter or print server instead.
# 3  
Old 04-18-2008
With SCO 6.0.0 install, the teo PCIe gives errors during start-up. After MP3, 'hw' lists them as "simple communication" after. Does this tell me that the parallel ports are working?
Login or Register to Ask a Question

Previous Thread | Next Thread

9 More Discussions You Might Find Interesting

1. Solaris

How to enable Serial port on ILOM, when Network Port is enabled in parallel

Hi Everyone, In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Discussion started by: bobby320
3 Replies

2. AIX

NPIV with 8Gb PCI Express Dual Port FC Adapter

All I am at a loss with a VIO server running ios 2.2.0.10-FP-24 SP-01. The VIO server is fitted with two 8Gb PCI Express Dual Port FC Adapters. However when I run the lsnports command only two of the adapter ports show as capable: $ lsnports name physloc ... (4 Replies)
Discussion started by: johnf
4 Replies

3. Fedora

Sending a byte to the parallel port

Greetings, A sort of newbie question... I would like to control a couple of stepper motors via the parallel port using C code. I have discovered in Linux, the ioperm() function is required before the outportb() function can be used to send a byte to the parallel port. My problem is ioperm()... (1 Reply)
Discussion started by: meyerga00
1 Replies

4. UNIX for Dummies Questions & Answers

Parallel port Printing in SCO OSR6

Hi, I am trying to add a parallel printer to my SCO OSR6 server, yet when I run mkdev parallel it just brings up the message: "Parallel Ports are configured automatically in SCO Openserver 6". So when I try and add a local printer, no /dev/lp# ports are shown in the list, only serial ports... (1 Reply)
Discussion started by: Martyn
1 Replies

5. SCO

PCI Express 1x HBA for parallel SCSI in Openserver 6

I'm floundering here trying to locate a PCI-E 1x HBA that will support an external tape drive in SCO Openserver 6. I was unable to find anything that would work in the compatible hardware list and a call to Adaptec confirmed that PCI-X would've been a better option for the risers in the Dell 2950... (1 Reply)
Discussion started by: s_mal
1 Replies

6. UNIX for Advanced & Expert Users

SCO openserver 6 parallel port issues

I am having issues with SCO recognizing my parallel port. The port is being used so I can run dialogic using a dongle for the serial number but the port is not noticed. It is turned on in the bios and should work fine but when I attempt to run the software I get errno=6 and it appears to not be... (0 Replies)
Discussion started by: shuhemizer
0 Replies

7. UNIX for Dummies Questions & Answers

SCO openserver 6 parallel port issues

I am having issues with SCO recognizing my parallel port. The port is being used so I can run dialogic using a dongle for the serial number but the port is not noticed. It is turned on in the bios and should work fine but when I attempt to run the software I get errno=6 and it appears to not be... (0 Replies)
Discussion started by: shuhemizer
0 Replies

8. Programming

parallel port proramming for sun ultra

Hi I'm trying to look for information about reading/writing to the parallel port of a Sun Ultra 5 running Solaris 8. I'd just like to see some basic programs written in C, nothing fancy, just reading and wrting to the port, getting the port address etc. toggling the lines. I've tried searching... (2 Replies)
Discussion started by: fishman2001
2 Replies

9. Filesystems, Disks and Memory

Parallel Port info?

is there a command so that i can se info about the parallel port, if there isn't a specific command for that is there a command so i can se info about the system and all ports and devices? Thanx /Nick (2 Replies)
Discussion started by: sajjan2
2 Replies
Login or Register to Ask a Question