10 More Discussions You Might Find Interesting
1. Solaris
Hi all,
this time I'd need a help from an advanced Solaris system admin :rolleyes:
I attached a HP StorageWorks Ultrium 215 Tape Drives - Overview - c00059530 - HP Business Support Center to my Sun E220R and it got recognized immediately (probe-scsi-all).
Now the operating system boot process... (8 Replies)
Discussion started by: pseudocoder
8 Replies
2. Hardware
I've had a scsi hard drive, scsi tape drive, and cd rom working off an adaptec 29160 controller. Everything worked great until a few days ago. I begin getting tar format errors (running sco 5.0.6) on the tape drive and occasionally the entire system would hang up while trying to access data on... (0 Replies)
Discussion started by: powwm
0 Replies
3. UNIX for Dummies Questions & Answers
Hi,
i installed a unix tape drive on my alphaserver. when i use a mt command it tells me there is no tape or device.
I have used the hardware manager and it shows the tape is present.
Can anyone help me understand why it cannot pick up the tape as a default? (1 Reply)
Discussion started by: ryks
1 Replies
4. UNIX for Dummies Questions & Answers
Currenty running SCO Openserver 6 at a Dell PowerEdge T300. I recently installed a driver for an Adaptec SCSI card (adpu320). When I connect a tape drive to it and re-start the system,it freezes and displays the following message: "WARNING: adpu320: Command timed out (ha= 4)" and the system... (2 Replies)
Discussion started by: RicardoM
2 Replies
5. Linux
Hello. I have Redhat 8.0 on a laptop. Working good.
I wanted to install the tape drive that is physically attached to it. The tape drive worked fine under Windows98SE. It's one of those parallel QIC-80 drives and I confirmed that it is supported by FTape. It appears that FTape might already... (0 Replies)
Discussion started by: RuralTurtle
0 Replies
6. Solaris
Hi,
I am a newbie to Solaris, I have a SunFire V120 box, i was trying to install a tape drive(HP SureStore DAT24), i did the install in this manner.
# rm -rf /etc/path_to_inst
# init 6
later at the "ok" prompt i gave "boot -ar" after doing that it asked me various options i accepted the... (2 Replies)
Discussion started by: rajendra.rait
2 Replies
7. Solaris
hi-
I just installed a quad gigaswift ethernet scsi card to my sunblade 150. I checked with the docs, and got all of the required drivers on the box. Now, I'm trying to mount an external scsi tape drive with no luck. I set the scsi address on the external drive to 0. Here's what I'm coming... (9 Replies)
Discussion started by: ECBROWN
9 Replies
8. Filesystems, Disks and Memory
Hi all, please help I am stuck.
I have installed a external unipack scsi tape drive. The tape drive is Exabyte Eliant 820. All I did was connected scsi cable and power it on. When issued "probe-scsi-all" command, the tape is correctly identified. However, when issued "dmesg | more" command, the... (4 Replies)
Discussion started by: dennis
4 Replies
9. Filesystems, Disks and Memory
I'm researching a tape drive + backup software to work across my unix/linux network. Was thinking about a dds4 tape drive (sony's) on my solaris ultra2, with some kind of software that would work across the network to back up my other 2 solaris boxes, plus my 2 linux boxes. What do others use... (3 Replies)
Discussion started by: kymberm
3 Replies
10. UNIX for Dummies Questions & Answers
I'm running SCO OS 505 on a Compaq proliant 1600, and my tape drive will just not work. It was working properly and whent to Sh?ts when I tried to get the cd rom working. I have uninstalled any configured tape drive and rebooted and then configured a tape drive and rebooted still nothing. I'm... (4 Replies)
Discussion started by: kikkin
4 Replies