10 More Discussions You Might Find Interesting
1. Red Hat
Hello community, I have a Proliant HP DL380P with the following network adapters:
NetXtreme BCM5719 Gigabit Ethernet PCIe (Ethernet 1Gb 4-port 331FLR Adapter)
82580 Gigabit Network Connection (NC365T 4-port Ethernet Server Adapter)
I installed Red Hat 7.2 but it recognizes only the... (9 Replies)
Discussion started by: Lord Spectre
i installed sco unix open server 5.0.7 on virtual machine vmware and runing it,
its work perfect and good.
now how i can configuare network at scoadmin that i able to access nework ?
---------- Post updated at 08:56 AM ---------- Previous update was at 01:47 AM ----------
nobody can... (2 Replies)
Discussion started by: farzad226
3. UNIX for Dummies Questions & Answers
I P2Vd a Unixware 7.1.4 box with VMWare Vsphere. I try to add a network adapter under Network Configuration Manager and it comes up with the error attached.
I've added a virtual adapter using the "E1000" option. It detects both the AMD PCI NET and E1000 virtual adapters under Network... (8 Replies)
Discussion started by: flashinwrx
4. UNIX for Dummies Questions & Answers
I am new here - this is my first post.
I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the... (1 Reply)
Discussion started by: soulmerchant
When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command:
entstat -all ent#|grep -i priority
Priority: 5 Active: False
How to make Active to True? (1 Reply)
Discussion started by: rainbow_bean
i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 )
what i need to do after the new adapter installed on the machine?
ariec (1 Reply)
Discussion started by: ariec
We have an old PC running on SCO Unix V. Is there any sites where i can get manual/procedures on how to install and configure Network. Thanks (2 Replies)
Discussion started by: nrcuevas
I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not... (1 Reply)
Discussion started by: johnf
I have got a Sco Unix Server, i want to connect some windows workstations. What configurations do i need to make on server and or workstation? (1 Reply)
Discussion started by: tpurazi1
10. UNIX for Dummies Questions & Answers
Our shops server runs SCO Openserver 5 release 5. It has two network cards in it (one on 10.0.0.6 and one on 188.8.131.52). When I run scoadmin and look at the network settings it show both my 3com network cards and a loop back driver http://theentertainer.com/james/untitled.jpg
Can anyone tell... (1 Reply)
Discussion started by: potter
RAY(4) BSD Kernel Interfaces Manual RAY(4)
ray -- Raytheon Raylink / WebGear Aviator IEEE 802.11 2Mbps Wireless
ray* at pcmcia? function ?
The ray device driver supports the Raytheon Raylink and Aviator 2.4/PRO 802.11 FH 2Mbps wireless PCMCIA cards. The cards can be operated in
either ad-hoc or infrastructure modes. The operating mode is selectable with ifconfig(8) through a media option.
To communicate with other 802.11 cards a common network id or NWID must be specified on each station that wishes to participate in the shared
wireless network. The NWID can be set with ifconfig(8).
The device uses IEEE 802.11 standard Frequency Hopping Spread Spectrum signaling and operates in the ranges of 2.400 to 2.4835 Gigahertz.
This frequency range is further restricted by country according to that country's regulations. Currently the ray driver defaults to using
the ranges appropriate for the USA. To change this setting you must define the kernel option RAY_PID_COUNTRY_CODE_DEFAULT to one of the fol-
The output power of the transceiver is 100mW and the card's power consumption is 365 mA @ 5 volts. The transmission range in open air (line
of sight) is a maximum of 1000 feet (or ~304 meters), and indoors (i.e., with obstructions) it is a maximum of 500 feet (152 meters).
Cards supported by the ray driver include:
WebGear Aviator 2.4
WebGear Aviator PRO
Raytheon Raylink WLAN
ray0: card failed self test: status x Indicates the card has failed its initial startup tests.
ifmedia(4), intro(4), pcmcia(4), ifconfig(8)
The ray driver first appeared in NetBSD 1.5.
The ray driver was written by Christian E. Hopps <chopps@NetBSD.org>.
Currently the infrastructure mode is untested, and authentication using WEP is unimplemented.
January 24, 2000 BSD