OK, I'm new to Unix (but an IT since DOS 6.2 era) Long story short I'm trying to help a friend who has failing Unix system which is perhaps 16 years old with SCO Openserver 3.4v4.2 with DDS90 Tape where they backup their data. I've setup a Dell Precision 390 with Unix 5.0.7 HW version and installed a Adaptec AHA-2940AU PCI card (on SCSI default ID 7) with Seagate Scorpion STD224000N Tape Drive (on SCSI ID 6). Question is how do I find the tape and how do I mount it so I can restore the data from the old machine to this.
Please help.
Thanks
Run:
The Adaptec controller is referred to as 'alad'
---------- Post updated at 06:32 AM ---------- Previous update was at 06:25 AM ----------
If the data on the backup tape is in tar format, then
should extract the data from the default tape drive.
The list of tar devices is maintained in /etc/default/tar.
The 'tape' command can be used to display the status of the drive.
Host adapter 0, it is the first and only host adapter in the computer.
Scsi bus is 0, this is only a single channel host adapter.
Target Id is 6 (the tape drive)
LUN is 0; as far as I know there have been no implementations of devices with logical unit numbers.
5.0.7 does not have automatic hardware recognition, so the host adapter does not show in the initial boot hardware list until the device driver for the host adapter (alad) is compiled into the kernel; which will happen during the running of 'mkdev tape'.
If this is working "jgt", I owe you for sure
More help and sorry for being a pest. 2 more things I need on this unit.
1 - I want to install a Parallel printer OKi Microline 521 (9 pin) to this machine. How do I add the printer? Their website has no Unix driver when I looked up!!
2 - I want to add terminal server to it so 2 workstation can login to it. They have EQUINOX ELS-II 16 PORT TERMINAL SERVER and also Equinox PM16-RJ Port Module. So whichever work. Have the PCI card to install with BNC and Terminal Server serial connection.
I'm again sorry for the troubles and picking your brains for it...
Dear all,
I have a AIX server with logical 3 partitions and the server is connecting a tape drive. the first partition can successfully making a system backup to the tape but how can i fail to mount the tape to second and thrid partition. would anyone can help me to deal with it? what command... (3 Replies)
Hi there: I'm new here
Can anyone help me:
I have DS15 Alpha server : Unix 5.1B
Now i need to connect a DLVT VS80 1U Rackmount Tape Drive unit.
What is the exact comman to mount the DLTape IV??
How do i make backuo @ copy file to the tape?
Thanx to all (0 Replies)
Hi,
Would appreciate if anyone could tell me if it is possible to mount (and use) a remote tape drive on a AIX server, and if so, what are the precise configuration steps needed?
The tape drive to be mounted as a remote tape drive is present on another AIX server in the same network.
... (5 Replies)
Hi,
Would appreciate if anyone could tell me if it is possible to mount (and use) a remote tape drive on a AIX server, and if so, what are the precise configuration steps needed?
The tape drive to be mounted as a remote tape drive is present on another AIX server in the same network.
... (0 Replies)
I'm trying to mount tape drive so I can tar from a cd.
this is what i type: mount /dev/rsd2940.4 /mnt
this is what i get: mount /dev/rsd2940.4 on /mnt : Block device required
I have no idea what that is supposed to mean. It's my understanding that rsd2940.4 is the block device. An... (1 Reply)
hi-
I just installed a quad gigaswift ethernet scsi card to my sunblade 150. I checked with the docs, and got all of the required drivers on the box. Now, I'm trying to mount an external scsi tape drive with no luck. I set the scsi address on the external drive to 0. Here's what I'm coming... (9 Replies)
Trying to mount a drive which has been dropped after corruption.
What is the quickets and esiest command to run and which switches? cheers
olly (1 Reply)